6 open source boards using the SN74LVC1G08DCKR
Real designs built with the SN74LVC1G08DCKR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Flipper blackhat
o7-machinehum
91 × 53.1 mm167 parts4LCC-BY-NC-4.0292FPGA
Hackrf pro
greatscottgadgets
120 × 75 mm503 parts6LCERN-OHL-P-2.063FPGA
GLOWCOST-2v2-mppcInterface-
tharinduudu
65 × 56.5 mm194 parts6LNo license1SCART switcher
nunosousa
255 × 127 mm595 parts4LNo license0STM32
Atlas drive
AtlasAutoware
140 × 90 mm377 parts6LNo license0ESP32
Leshy2 LESHY2-UI-R2 R2 exact placement
anton-vinogradov
80 × 150 mm430 parts6LMIT6
How designs wire the SN74LVC1G08DCKR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the SN74LVC1G08DCKR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 5 of 6 designs, most often 1 µF (then 100 nF).
- The Y pin has a series resistor on 3 of 6 designs, most often 68 Ω (then 4.7 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Bpin 2 | Connected to: A connector 33% |
|
| GNDpin 3 | Connected to: GND 83% · a signal 17% | — |
| Ypin 4 | Connected to: Signal 100% |
|
| VCCpin 5 | Connected to: 3.3V 67% · a signal 33% |
|
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Flipper blackhat by o7-machinehum, Hackrf pro by greatscottgadgets, Leshy2 LESHY2-UI-R2 R2 exact placement by anton-vinogradov and GLOWCOST-2v2-mppcInterface- by tharinduudu.
The SN74LVC1G08DCKR in open source designs
The gallery holds 6 open source boards using the SN74LVC1G08DCKR from 6 GitHub repositories; a typical one measures about 105.5 × 82.5 mm and carries around 404 components.
100% use four copper layers or more, and 33% carry an open source license.
The most starred is Flipper blackhat by o7-machinehum.
Parts used alongside the SN74LVC1G08DCKR
What boards using the SN74LVC1G08DCKR are built for
SN74LVC1G08DCKR: common questions
Where can I find a SN74LVC1G08DCKR reference design?
Each of the 6 boards on this page is a real design using the SN74LVC1G08DCKR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the SN74LVC1G08DCKR VCC pin?
The VCC pin has a decoupling capacitor on 5 of 6 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 6 open source designs using the SN74LVC1G08DCKR.
What resistor goes on the SN74LVC1G08DCKR Y pin?
The Y pin has a series resistor on 3 of 6 designs, most often 68 Ω (then 4.7 kΩ). Counted from the KiCad layouts of 6 open source designs using the SN74LVC1G08DCKR.
Which microcontrollers do boards using the SN74LVC1G08DCKR use?
Most are built on FPGA (2), ESP32 (1) and STM32 (1).
How big is a typical board using the SN74LVC1G08DCKR?
The median is 105.5 × 82.5 mm, and 0% are two-layer designs.
What is the most popular open source board using the SN74LVC1G08DCKR?
By GitHub stars, Flipper blackhat by o7-machinehum, with 292 stars.
Can I simulate one of these boards using the SN74LVC1G08DCKR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.