5 open source boards using the STSPIN220
Real designs built with the STSPIN220, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Mini motor controller
Jana-Marie
28.2 × 24.5 mm39 parts2LCERN-OHL-S-2.013STM32
JUCI CubeSat SADA
makerCL
83 × 55 mm134 parts4LNo license2ESP32
Isc motorbeep
ISC-HEI
70 × 50 mm69 parts4LNo license0Vision-Robot-Electronics
keionbis
41 × 49.9 mm49 parts2LNo license0ESP32
MiniBot
DDeGonge
21.2 × 28 mm58 parts4LMIT40
How designs wire the STSPIN220
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the STSPIN220 connects to, and the resistors, capacitors and other passives placed on it.
- The SENSEA pin has a resistor to GND on 5 of 5 designs, most often 330 mΩ (then 1 Ω).
- The VS pin has a decoupling capacitor on 5 of 5 designs, most often 10 µF (then 22 µF).
- The SENSEB pin has a resistor to GND on 5 of 5 designs, most often 330 mΩ (then 1 Ω).
- The TOFF pin has a resistor to GND on 5 of 5 designs, most often 47 kΩ (then 22.1 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SENSEApin 4 | Connected to: Signal 100% |
|
| VSpin 6 | Connected to: BATT 60% · a signal 40% |
|
| GNDpin 7 | Connected to: GND 100% | — |
| SENSEBpin 9 | Connected to: Signal 100% |
|
| REFpin 11 | Connected to: Signal 80% · VREF 20% |
|
| TOFFpin 12 | Connected to: Signal 100% |
|
| EN/FLTpin 13 | Connected to: The microcontroller 60% |
|
| STBY/RESETpin 14 | Connected to: The microcontroller 60%, STSPIN220 40% · BATT 20% |
|
| EPADpin 17 | Connected to: GND 100% | — |
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MiniBot by DDeGonge, Mini motor controller by Jana-Marie, JUCI CubeSat SADA by makerCL and Isc motorbeep by ISC-HEI.
The STSPIN220 in open source designs
The gallery holds 5 open source boards using the STSPIN220 from 5 GitHub repositories; a typical one measures about 41 × 49.9 mm and carries around 58 components.
60% use four copper layers or more, and 40% carry an open source license.
The most starred is MiniBot by DDeGonge.
Parts used alongside the STSPIN220
What boards using the STSPIN220 are built for
STSPIN220: common questions
Where can I find a STSPIN220 reference design?
Each of the 5 boards on this page is a real design using the STSPIN220. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the STSPIN220 SENSEA pin?
The SENSEA pin has a resistor to GND on 5 of 5 designs, most often 330 mΩ (then 1 Ω). Counted from the KiCad layouts of 5 open source designs using the STSPIN220.
What decoupling capacitors do designs use on the STSPIN220 VS pin?
The VS pin has a decoupling capacitor on 5 of 5 designs, most often 10 µF (then 22 µF). Counted from the KiCad layouts of 5 open source designs using the STSPIN220.
What resistor goes on the STSPIN220 SENSEB pin?
The SENSEB pin has a resistor to GND on 5 of 5 designs, most often 330 mΩ (then 1 Ω). Counted from the KiCad layouts of 5 open source designs using the STSPIN220.
Which microcontrollers do boards using the STSPIN220 use?
Most are built on ESP32 (2) and STM32 (2).
How big is a typical board using the STSPIN220?
The median is 41 × 49.9 mm, and 40% are two-layer designs.
What is the most popular open source board using the STSPIN220?
By GitHub stars, MiniBot by DDeGonge, with 40 stars.
Can I simulate one of these boards using the STSPIN220 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.