7 open source boards using the TLA2528IRTER

Real designs built with the TLA2528IRTER, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the TLA2528IRTER

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TLA2528IRTER connects to, and the resistors, capacitors and other passives placed on it.

  • The AVDD pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 1 µF).
  • The DECAP pin has a capacitor to GND on 6 of 6 designs, most often 1 µF.
  • The DVDD pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 1 µF).
  • The SCL pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ (then 4.7 kΩ).
AIN2/GPIO2pin 1Connected to: Signal 67% · not connected 33%
  • Series resistor on 50% · 1 kΩ (2), 0 Ω (1)
  • Capacitor to GND on 33% · 100 nF (2)
  • Resistor to GND on 33% · 10 MΩ (1)
AIN3/GPIO3pin 2Connected to: Signal 67% · not connected 33%
  • Capacitor to GND on 33% · 100 nF (2)
AIN4/GPIO4pin 3Connected to: Signal 67% · not connected 33%
  • Capacitor to GND on 33% · 10 nF (1), 100 nF (1)
AIN5/GPIO5pin 4Connected to: Signal 67% · not connected 33%
  • Series resistor on 50% · 100 Ω (1), 1 kΩ (1), 10 kΩ (1)
  • Capacitor to GND on 33% · 10 nF (1), 100 nF (1)
  • Resistor to GND on 33% · 10 MΩ (1), 3.32 kΩ (1)
AIN6/GPIO6pin 5Connected to: Signal 67% · not connected 33%
  • Series resistor on 33% · 1 kΩ (1), 10 kΩ (1)
  • Resistor to GND on 33% · 10 kΩ (2)
  • Pull-up to 3.3V on 33% · 10 kΩ (2)
AIN7/GPIO7pin 6Connected to: Signal 67% · not connected 33%
  • Pull-up to 5.5V on 50% · 10 kΩ (3)
  • Resistor to GND on 50% · 10 kΩ (3)
AVDDpin 7Connected to: 5.5V 83% · a signal 17%
  • Decoupling capacitor on 100% · 100 nF (6), 1 µF (2)
DECAPpin 8Connected to: Signal 100%
  • Capacitor to GND on 100% · 1 µF (6)
  • Series resistor on 33% · 0 Ω (1), 999 MΩ (1)
GNDpin 9Connected to: GND 100%
DVDDpin 10Connected to: 3.3V 100%
  • Decoupling capacitor on 100% · 100 nF (7), 1 µF (1)
ADDRpin 11Connected to: Not connected 50% · a signal 50%
  • Series resistor on 33% · 0 Ω (1), 999 MΩ (1)
  • Resistor to GND on 33% · 33 kΩ (1)
NCpin 12Connected to: Not connected 100%
SCLpin 13Connected to: TCA6408ARGTR 50%, TMP117AIDRVR 33%, a connector 33%
  • Pull-up to 3.3V on 83% · 10 kΩ (3), 4.7 kΩ (1), 1.6 kΩ (1)
  • Series resistor on 33% · 121 Ω (3), 22 Ω (1)
SDApin 14Connected to: TCA6408ARGTR 50%, TMP117AIDRVR 33%, a connector 33%
  • Pull-up to 3.3V on 83% · 10 kΩ (3), 4.7 kΩ (1), 1.6 kΩ (1)
  • Series resistor on 33% · 121 Ω (3), 22 Ω (1)
AIN0/GPIO0pin 15Connected to: AD8363ACPZ-R7 33%
  • Resistor to GND on 67% · 1.8 kΩ (1), 10 kΩ (1)
  • Series resistor on 50% · 0 Ω (2), 1 kΩ (1)
  • Capacitor to GND on 33% · 100 nF (2)
  • Pull-up to 15V on 33% · 10 kΩ (2)
EPpin 17Connected to: GND 100%

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PROJ500 - Power Supply Board by AislingBee, ETH1CFGEN1 by BehrensG, MecProInverter by Eg0st and FRX by EIGSEP.

The TLA2528IRTER in open source designs

The gallery holds 7 open source boards using the TLA2528IRTER from 6 GitHub repositories; a typical one measures about 60.1 × 45.2 mm and carries around 153 components.

86% use four copper layers or more, and 29% carry an open source license.

The most starred is ETH1CFGEN1 by BehrensG.

Microcontrollers on boards using the TLA2528IRTER

What boards using the TLA2528IRTER are built for

TLA2528IRTER: common questions

Where can I find a TLA2528IRTER reference design?

Each of the 7 boards on this page is a real design using the TLA2528IRTER. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the TLA2528IRTER AVDD pin?

The AVDD pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the TLA2528IRTER.

How is the TLA2528IRTER DECAP pin connected?

The DECAP pin has a capacitor to GND on 6 of 6 designs, most often 1 µF. Counted from the KiCad layouts of 6 open source designs using the TLA2528IRTER.

What decoupling capacitors do designs use on the TLA2528IRTER DVDD pin?

The DVDD pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the TLA2528IRTER.

What parts are used alongside the TLA2528IRTER?

The AD8363ACPZ-R7, F1958NBGK, INA296B4IDDFR, PAT1220-C-3DB-T5 and PGA-105+ appear in the most repositories here.

Which microcontrollers do boards using the TLA2528IRTER use?

Most are built on ESP32 (1) and STM32 (1).

How big is a typical board using the TLA2528IRTER?

The median is 60.1 × 45.2 mm, and 14% are two-layer designs.

What is the most popular open source board using the TLA2528IRTER?

By GitHub stars, ETH1CFGEN1 by BehrensG, with 0 stars.

Can I simulate one of these boards using the TLA2528IRTER before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part