10 open source boards using the TLP250
Real designs built with the TLP250, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AI Inverter Project
HNadeemTahir
304.6 × 105.7 mm115 parts2LNo license33P-VVVF
53175ddd
95 × 72 mm31 parts2LNo license1PCB HORNO
Bojtronic
226.2 × 263.7 mm249 parts2LNo license0ESP8266
Pressure measuring and control-Board
Mohamed-U3
100 × 100 mm125 parts2LMIT0Chb inverter
feaksel
209.6 × 120.7 mm95 parts2LApache-2.00Optocoupler
JaVD054
149.7 × 99.7 mm34 parts2LNo license0Buck
Mehmet-Emre-Dogan
85 × 105 mm15 parts2LNo license0- schematic only · 97 partsSTM32
Autonomous Ackermann
sachu018
97 partsNo license0 Protection
aykutozdemir
65 × 80 mm69 parts2LNo license0Bldcdriver
22060
68.6 × 33 mm45 parts2LNo license0
How designs wire the TLP250
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the TLP250 connects to, and the resistors, capacitors and other passives placed on it.
- The A pin has a series resistor on 8 of 9 designs, most often 1.3 kΩ (then 270 Ω).
- The VO pins have a series resistor on 8 of 9 designs, most often 15 Ω (then 10 Ω).
- The C pin is tied to GND on 8 of 9 designs.
- The VCC pin has a capacitor to GND on 4 of 9 designs, most often 100 nF (then 1 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NCpin 1, 4 | Connected to: Not connected 100% | — |
| Apin 2 | Connected to: Signal 100% |
|
| Cpin 3 | Connected to: GND 89% | — |
| VEEpin 5 | Connected to: A connector 33% · GND 44% |
|
| VOpin 6, 7 | Connected to: Signal 83% · not connected 17% |
|
| VCCpin 8 | Connected to: Signal 56% · 15V 44% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AI Inverter Project by HNadeemTahir, 3P-VVVF by 53175ddd, Bldcdriver by 22060 and Protection by aykutozdemir.
The TLP250 in open source designs
The gallery holds 10 open source boards using the TLP250 from 10 GitHub repositories; a typical one measures about 100 × 100 mm and carries around 82 components.
100% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is AI Inverter Project by HNadeemTahir.
What boards using the TLP250 are built for
TLP250: common questions
Where can I find a TLP250 reference design?
Each of the 10 boards on this page is a real design using the TLP250. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TLP250 A pin?
The A pin has a series resistor on 8 of 9 designs, most often 1.3 kΩ (then 270 Ω). Counted from the KiCad layouts of 9 open source designs using the TLP250.
What resistor goes on the TLP250 VO pin?
The VO pins have a series resistor on 8 of 9 designs, most often 15 Ω (then 10 Ω). Counted from the KiCad layouts of 9 open source designs using the TLP250.
How is the TLP250 C pin connected?
The C pin is tied to GND on 8 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the TLP250.
Which microcontrollers do boards using the TLP250 use?
Most are built on ESP8266 (1) and STM32 (1).
How big is a typical board using the TLP250?
The median is 100 × 100 mm, and 100% are two-layer designs.
What is the most popular open source board using the TLP250?
By GitHub stars, AI Inverter Project by HNadeemTahir, with 3 stars.
Can I simulate one of these boards using the TLP250 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.