5 open source boards using the TMI7003C
Real designs built with the TMI7003C, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
WCH CH32/CH55x
SandKrux
sandman21vs
58.3 × 98.2 mm163 parts2LNo license21FPGA
Tangnano9k kr260-hat
calperxd
65 × 56.5 mm168 parts4LCustom license0AVR/Arduino
Linux soc
NEOgHacking
25.5 × 32 mm73 parts4LNo license0Linux soc
KOEGlike
25.5 × 32 mm57 parts2LGPL-3.06Linux soc
hackclub
25.5 × 32 mm57 parts2LGPL-3.05
How designs wire the TMI7003C
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TMI7003C connects to, and the resistors, capacitors and other passives placed on it.
- The FB3_2 pin has a resistor to GND on 5 of 5 designs, most often 62 kΩ (then 150 kΩ).
- The FB2_3 pin has a resistor to GND on 5 of 5 designs, most often 15 kΩ (then 150 kΩ).
- The LX2_6 pin has a inductor on 5 of 5 designs, most often 2.2 µH.
- The VIN2_7 pin has a decoupling capacitor on 5 of 5 designs, most often 22 µF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NC_1pin 1 | Connected to: Not connected 60% · GND 40% | — |
| FB3_2pin 2 | Connected to: Signal 100% |
|
| FB2_3pin 3 | Connected to: Signal 100% |
|
| NC_4pin 4 | Connected to: Not connected 60% · GND 40% | — |
| NC_5pin 5 | Connected to: Not connected 60% · GND 40% | — |
| LX2_6pin 6 | Connected to: Signal 100% |
|
| VIN2_7pin 7 | Connected to: 3.3V 100% |
|
| EN2_8pin 8 | Connected to: 3.3V 100% |
|
| EN1_9pin 9 | Connected to: 5V 100% | — |
| VIN1_10pin 10 | Connected to: 5V 100% |
|
| LX1_11pin 11 | Connected to: Signal 100% |
|
| NC_12pin 12 | Connected to: Not connected 60% · GND 40% | — |
| NC_13pin 13 | Connected to: Not connected 60% · GND 40% | — |
| FB1_14pin 14 | Connected to: Signal 100% |
|
| NC_15pin 15 | Connected to: Not connected 60% · GND 40% | — |
| NC_16pin 16 | Connected to: Not connected 60% · 5V 40% |
|
| NC_17pin 17 | Connected to: Not connected 60% · GND 40% | — |
| EN3_18pin 18 | Connected to: 3.3V 100% |
|
| VIN3_19pin 19 | Connected to: 3.3V 100% |
|
| LX3_20pin 20 | Connected to: Signal 100% |
|
| GND_21pin 21 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include SandKrux by sandman21vs, Linux soc by KOEGlike, Linux soc by hackclub and Tangnano9k kr260-hat by calperxd.
The TMI7003C in open source designs
The gallery holds 5 open source boards using the TMI7003C from 5 GitHub repositories; a typical one measures about 25.5 × 32 mm and carries around 73 components.
60% are two-layer designs, the rest use four layers or more, and 40% carry an open source license.
The most starred is SandKrux by sandman21vs.
Parts used alongside the TMI7003C
Microcontrollers on boards using the TMI7003C
What boards using the TMI7003C are built for
TMI7003C: common questions
Where can I find a TMI7003C reference design?
Each of the 5 boards on this page is a real design using the TMI7003C. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TMI7003C FB3_2 pin?
The FB3_2 pin has a resistor to GND on 5 of 5 designs, most often 62 kΩ (then 150 kΩ). Counted from the KiCad layouts of 5 open source designs using the TMI7003C.
What resistor goes on the TMI7003C FB2_3 pin?
The FB2_3 pin has a resistor to GND on 5 of 5 designs, most often 15 kΩ (then 150 kΩ). Counted from the KiCad layouts of 5 open source designs using the TMI7003C.
How is the TMI7003C LX2_6 pin connected?
The LX2_6 pin has a inductor on 5 of 5 designs, most often 2.2 µH. Counted from the KiCad layouts of 5 open source designs using the TMI7003C.
Which microcontrollers do boards using the TMI7003C use?
Most are built on AVR/Arduino (1), WCH CH32/CH55x (1) and FPGA (1).
How big is a typical board using the TMI7003C?
The median is 25.5 × 32 mm, and 60% are two-layer designs.
What is the most popular open source board using the TMI7003C?
By GitHub stars, SandKrux by sandman21vs, with 21 stars.
Can I simulate one of these boards using the TMI7003C before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.