12 open source boards using the F1C100s
Real designs built with the F1C100s, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
M5Pi-F1C100S/200S
imliubo
47.5 × 50 mm141 parts4LNo license197Ecad viewer
Huaqiu-Electronics
47.5 × 50 mm141 parts4LMIT91Tuxkeychain
electron271
50 × 60 mm45 parts6LCC-BY-SA-4.017F1c200s dev board
Mr-Bossman
62 × 46 mm58 parts2LNo license16ESP32
Sbc allwinner F1C200s
vd-rd
60 × 44 mm105 parts4LNo license7ESP32
Network player
naguirre
30.1 × 66.6 mm72 parts4LMIT3AVR/Arduino
Linux soc
NEOgHacking
25.5 × 32 mm73 parts4LNo license0ESP32
Network player
naguirre
30.1 × 66.6 mm72 parts4LNo license0Business card
whateverany-org
90 × 54.5 mm44 parts2LUnlicense0Linux soc
KOEGlike
25.5 × 32 mm57 parts2LGPL-3.06Linux soc
hackclub
25.5 × 32 mm57 parts2LGPL-3.05Raspberry Pi
Dac
naguirre
30.1 × 65.1 mm23 parts2LNo license0
How designs wire the F1C100s
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the F1C100s connects to, and the resistors, capacitors and other passives placed on it.
- The VCC_IO pins have a decoupling capacitor on 10 of 10 designs, most often 100 nF (then 2.2 µF).
- The VDD_CORE pins have a decoupling capacitor on 10 of 10 designs, most often 100 nF (then 1 µF).
- The SVREF pin has a resistor to GND on 10 of 10 designs, most often 2.2 kΩ (then 2 kΩ).
- The SVREF pin has a pull-up to 2.5V on 10 of 10 designs, most often 2.2 kΩ (then 2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| HPLpin 1 | Connected to: Not connected 64% · a signal 36% | — |
| HPCOMpin 3 | Connected to: Not connected 73% · a signal 27% | — |
| HPVCCpin 4 | Connected to: 3.3V 73% · not connected 27% |
|
| VCC_IOpin 5, 20, 50 | Connected to: 3.3V 100% |
|
| PD7/LCD_D11/DA_MCLK/EINTpin 13 | Connected to: A connector 40% · not connected 30% |
|
| PD8/LCD_D12/DA_BCLK/EINTpin 14 | Connected to: Not connected 60% · a signal 40% | — |
| PD9/LCD_D13/DA_LRCK/EINTpin 15 | Connected to: Not connected 60% · a signal 40% | — |
| PD10/LCD_D14/DA_IN/EINTDpin 16 | Connected to: Not connected 60% · a signal 40% | — |
| PD11/LCD_D15/DA_OUT/EINTpin 17 | Connected to: Not connected 60% · a signal 40% | — |
| PD13/LCD_D19/UART2_TX/EIpin 19 | Connected to: Not connected 60% · a signal 40% | — |
| PD14/LCD_D20/UART2_RX/EIpin 21 | Connected to: Not connected 60% · a signal 40% | — |
| VDD_COREpin 22, 35, 71 | Connected to: 1.1V 100% |
|
| PD17/LCD_D23/OWA_OUT/EINpin 25 | Connected to: Not connected 70% · a signal 30% | — |
| VCC_DRAMpin 30, 31, 32, 34, 36 | Connected to: 2.5V 100% |
|
| SVREFpin 33 | Connected to: Signal 100% |
|
| PE11/CLK_OUT/TWI0_SCK/IRpin 38 | Connected to: A connector 50%, MPU-6050 20% · not connected 40% |
|
| PE2/CSI_PCLK/LCD_D8/CLK_pin 47 | Connected to: Not connected 60% · a signal 40% |
|
| HOSCIpin 51 | Connected to: Signal 100% |
|
| HOSCOpin 52 | Connected to: Signal 100% |
|
| PF5/SDC0_D2/DBG_CK/PWM1/pin 53 | Connected to: A connector 90% |
|
| PF4/SDC0_D3/UART0_TX/EINpin 54 | Connected to: A connector 90% |
|
| PF3/SDC0_CMD/DBG_DO/EINTpin 55 | Connected to: A connector 90% |
|
| PF1/SDC0_D0/DBG_DI/EINTFpin 57 | Connected to: A connector 90% |
|
| PF0/SDC0_D1/DBG_MS/IR_RXpin 58 | Connected to: A connector 90% |
|
| PC1/SPI0_CS/SDC1_CMDpin 60 | Connected to: A connector 60%, ESP8089 20%, AT25SF081-SSHD-X 20% |
|
| UVCCpin 67 | Connected to: 3.3V 100% |
|
| USB-DMpin 68 | Connected to: A connector 60% |
|
| USB-DPpin 69 | Connected to: A connector 60% |
|
| RESETpin 70 | Connected to: A connector 50% |
|
| TVOUTpin 72 | Connected to: Not connected 80% · a signal 20% | — |
| TV_VCCpin 73 | Connected to: 3.3V 70% · not connected 30% |
|
| TVGNDpin 74 | Connected to: GND 100% | — |
| TV_VRNpin 75 | Connected to: Not connected 80% · a signal 20% | — |
| TV_VRPpin 76 | Connected to: Not connected 80% · a signal 20% | — |
| TVIN1pin 77 | Connected to: Not connected 90% | — |
| TVIN0pin 78 | Connected to: Not connected 90% | — |
| LRADC0pin 79 | Connected to: Not connected 70% · a signal 30% | — |
| AVCCpin 80 | Connected to: 3V 70% · not connected 30% |
|
| VRA1pin 81 | Connected to: Not connected 60% · a signal 40% |
|
| AGNDpin 82 | Connected to: GND 100% | — |
41 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include M5Pi-F1C100S/200S by imliubo, Ecad viewer by Huaqiu-Electronics, Tuxkeychain by electron271 and F1c200s dev board by Mr-Bossman.
The F1C100s in open source designs
The gallery holds 12 open source boards using the F1C100s from 11 GitHub repositories; a typical one measures about 38.8 × 50 mm and carries around 65 components.
58% use four copper layers or more, and 50% carry an open source license.
The most starred is M5Pi-F1C100S/200S by imliubo.
Parts used alongside the F1C100s
Microcontrollers on boards using the F1C100s
What boards using the F1C100s are built for
F1C100s: common questions
Where can I find a F1C100s reference design?
Each of the 12 boards on this page is a real design using the F1C100s. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the F1C100s VCC_IO pin?
The VCC_IO pins have a decoupling capacitor on 10 of 10 designs, most often 100 nF (then 2.2 µF). Counted from the KiCad layouts of 11 open source designs using the F1C100s.
What decoupling capacitors do designs use on the F1C100s VDD_CORE pin?
The VDD_CORE pins have a decoupling capacitor on 10 of 10 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 11 open source designs using the F1C100s.
What resistor goes on the F1C100s SVREF pin?
The SVREF pin has a resistor to GND on 10 of 10 designs, most often 2.2 kΩ (then 2 kΩ). Counted from the KiCad layouts of 11 open source designs using the F1C100s.
What parts are used alongside the F1C100s?
The TMI7003C, AT25SF081-SSHD-X, CH340E, EA3036 and ESP32-C3-MINI-1 appear in the most repositories here.
Which microcontrollers do boards using the F1C100s use?
Most are built on ESP32 (3), AVR/Arduino (1) and Raspberry Pi (1).
How big is a typical board using the F1C100s?
The median is 38.8 × 50 mm, and 42% are two-layer designs.
What is the most popular open source board using the F1C100s?
By GitHub stars, M5Pi-F1C100S/200S by imliubo, with 197 stars.
Can I simulate one of these boards using the F1C100s before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.