6 open source boards using the TPS2065CDBV
Real designs built with the TPS2065CDBV, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Hw openmower yardforce
xtech
180 × 170 mm275 parts4LCC-BY-4.012ESP32
Dude dirty usb disconnect
ldab
40 × 50 mm36 parts2LWTFPL1RP2040/RP2350
Adventure board
picorubykaigi
90 × 130 mm361 parts4LCERN-OHL-P-2.00STM32
XYmatics-E64
XyrusB2010
191.3 × 97.8 mm277 parts2LNo license0ESP32
Prod board
family-mruby
90 × 70 mm125 parts4LCERN-OHL-S-2.00ESP32
Dev board r2
family-mruby
90 × 70 mm109 parts4LCERN-OHL-S-2.00
How designs wire the TPS2065CDBV
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TPS2065CDBV connects to, and the resistors, capacitors and other passives placed on it.
- The IN pin is tied to VBUS on 5 of 5 designs.
- The FLT pin has a pull-up to VBUS on 4 of 5 designs, most often 10 kΩ (then 5.1 kΩ).
- The OUT pin is tied to 5V on 3 of 5 designs (a signal on 2).
- The EN pin is tied to VBUS on 3 of 5 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUTpin 1 | Connected to: 5V 60% · a signal 40% | — |
| GNDpin 2 | Connected to: GND 100% | — |
| FLTpin 3 | Connected to: Signal 80% · not connected 20% |
|
| ENpin 4 | Connected to: VBUS 60% · a signal 40% | — |
| INpin 5 | Connected to: VBUS 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hw openmower yardforce by xtech, Dude dirty usb disconnect by ldab, Dev board r2 by family-mruby and Adventure board pcb by picorubykaigi.
The TPS2065CDBV in open source designs
The gallery holds 6 open source boards using the TPS2065CDBV from 5 GitHub repositories; a typical one measures about 90 × 83.9 mm and carries around 200 components.
67% use four copper layers or more, and 83% carry an open source license.
The most starred is Hw openmower yardforce by xtech.
Parts used alongside the TPS2065CDBV
Microcontrollers on boards using the TPS2065CDBV
What boards using the TPS2065CDBV are built for
TPS2065CDBV: common questions
Where can I find a TPS2065CDBV reference design?
Each of the 6 boards on this page is a real design using the TPS2065CDBV. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS2065CDBV IN pin connected?
The IN pin is tied to VBUS on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TPS2065CDBV.
What pull-up resistor is used on the TPS2065CDBV FLT pin?
The FLT pin has a pull-up to VBUS on 4 of 5 designs, most often 10 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 5 open source designs using the TPS2065CDBV.
How is the TPS2065CDBV OUT pin connected?
The OUT pin is tied to 5V on 3 of 5 designs (a signal on 2). Counted from the KiCad layouts of 5 open source designs using the TPS2065CDBV.
Which microcontrollers do boards using the TPS2065CDBV use?
Most are built on ESP32 (3), AVR/Arduino (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the TPS2065CDBV?
The median is 90 × 83.9 mm, and 33% are two-layer designs.
What is the most popular open source board using the TPS2065CDBV?
By GitHub stars, Hw openmower yardforce by xtech, with 12 stars.
Can I simulate one of these boards using the TPS2065CDBV before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.