6 open source boards using the TPS2561DRCR
Real designs built with the TPS2561DRCR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
1026-RPi-Power-Hat
wilsondr9999
85 × 56.5 mm121 parts4LCC-BY-SA-4.09FPGA
QSIC
dabridgham
214.1 × 131.8 mm212 parts6LNo license2RP2040/RP2350
FinalProject
leomotors
100 × 100 mm139 parts2LNo license1Raspberry Pi
Usb3.1-Ethernet-RP2040-I2S HUB
Tanawin1701d
100 × 100 mm136 parts4LNo license1HighSpeedUSBHub
Acidicts
80.6 × 57 mm86 parts4LNo license0Ovc5
osrf
98 × 97 mm197 parts6LApache-2.0207
How designs wire the TPS2561DRCR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the TPS2561DRCR connects to, and the resistors, capacitors and other passives placed on it.
- The ILIM pin has a resistor to GND on 6 of 6 designs, most often 25.5 kΩ (then 47 kΩ).
- The IN pins is tied to 5V on 100% of them.
- The OUT2 pin has a capacitor to GND on 5 of 6 designs, most often 150 µF (then 100 nF).
- The FAULT2 pin has a pull-up to 3.3V on 4 of 6 designs, most often 10 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| INpin 2, 3 | Connected to: 5V 100% | — |
| EN1pin 4 | Connected to: Signal 83% · GND 17% |
|
| EN2pin 5 | Connected to: Signal 100% |
|
| FAULT2pin 6 | Connected to: Signal 100% |
|
| ILIMpin 7 | Connected to: Signal 100% |
|
| OUT2pin 8 | Connected to: Signal 83% · VBUS_SW_1 17% |
|
| OUT1pin 9 | Connected to: Signal 67% · not connected 17% · VBUS_SW_0 17% |
|
| FAULT1pin 10 | Connected to: Signal 100% |
|
| PADpin 11 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ovc5 by osrf, 1026-RPi-Power-Hat by wilsondr9999, QSIC by dabridgham and FinalProject by leomotors.
The TPS2561DRCR in open source designs
The gallery holds 6 open source boards using the TPS2561DRCR from 6 GitHub repositories; a typical one measures about 99 × 98.5 mm and carries around 138 components.
83% use four copper layers or more, and 33% carry an open source license.
The most starred is Ovc5 by osrf.
Parts used alongside the TPS2561DRCR
Microcontrollers on boards using the TPS2561DRCR
What boards using the TPS2561DRCR are built for
TPS2561DRCR: common questions
Where can I find a TPS2561DRCR reference design?
Each of the 6 boards on this page is a real design using the TPS2561DRCR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the TPS2561DRCR ILIM pin?
The ILIM pin has a resistor to GND on 6 of 6 designs, most often 25.5 kΩ (then 47 kΩ). Counted from the KiCad layouts of 6 open source designs using the TPS2561DRCR.
How is the TPS2561DRCR IN pin connected?
The IN pins is tied to 5V on 100% of them. Counted from the KiCad layouts of 6 open source designs using the TPS2561DRCR.
How is the TPS2561DRCR OUT2 pin connected?
The OUT2 pin has a capacitor to GND on 5 of 6 designs, most often 150 µF (then 100 nF). Counted from the KiCad layouts of 6 open source designs using the TPS2561DRCR.
Which microcontrollers do boards using the TPS2561DRCR use?
Most are built on FPGA (1), Raspberry Pi (1) and RP2040/RP2350 (1).
How big is a typical board using the TPS2561DRCR?
The median is 99 × 98.5 mm, and 17% are two-layer designs.
What is the most popular open source board using the TPS2561DRCR?
By GitHub stars, Ovc5 by osrf, with 207 stars.
Can I simulate one of these boards using the TPS2561DRCR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.