5 open source boards using the TPS62A02DRLR
Real designs built with the TPS62A02DRLR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Thunderscope Rev5.3
EEVengers
122.5 × 103.5 mm817 parts6LMIT1.3kFPGA
SIG COND
Han-ZenX
122.5 × 103.5 mm817 parts6LCustom license1ESP32
Dpf load monitor wide
v-cu
50 × 23 mm106 parts6LCC-BY-NC-4.01STM32
Grippyboi
gabbla
68 × 100 mm193 parts4LNo license0RP2040/RP2350
Tc2-main
TheCacophonyProject
73 × 75.5 mm161 parts6LCERN-OHL-W-2.00
How designs wire the TPS62A02DRLR
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TPS62A02DRLR connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 5 of 5 designs, most often 1 µH.
- The VIN pin has a decoupling capacitor on 5 of 5 designs, most often 10 µF (then 100 nF).
- The FB pin has a resistor to GND on 4 of 5 designs, most often 20 kΩ (then 10 kΩ).
- The PG pin is left unconnected on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| SWpin 2 | Connected to: Signal 80% · 1.2V 20% |
|
| VINpin 3 | Connected to: VUSB 80% · a signal 20% |
|
| ENpin 4 | Connected to: TPS62A02DRLR 40%, TPS7A9101DSKR 40%, the microcontroller 40% |
|
| FBpin 5 | Connected to: Signal 80% · 1.2V 20% |
|
| PGpin 6 | Connected to: Not connected 80% · a signal 20% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Thunderscope Rev5.3 by EEVengers, SIG COND by Han-ZenX, Dpf load monitor wide by v-cu and Grippyboi by gabbla.
The TPS62A02DRLR in open source designs
The gallery holds 5 open source boards using the TPS62A02DRLR from 5 GitHub repositories; a typical one measures about 73 × 100 mm and carries around 193 components.
100% use four copper layers or more, and 40% carry an open source license.
The most starred is Thunderscope Rev5.3 by EEVengers.
Parts used alongside the TPS62A02DRLR
Microcontrollers on boards using the TPS62A02DRLR
What boards using the TPS62A02DRLR are built for
TPS62A02DRLR: common questions
Where can I find a TPS62A02DRLR reference design?
Each of the 5 boards on this page is a real design using the TPS62A02DRLR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS62A02DRLR SW pin connected?
The SW pin has a inductor on 5 of 5 designs, most often 1 µH. Counted from the KiCad layouts of 5 open source designs using the TPS62A02DRLR.
What decoupling capacitors do designs use on the TPS62A02DRLR VIN pin?
The VIN pin has a decoupling capacitor on 5 of 5 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the TPS62A02DRLR.
What resistor goes on the TPS62A02DRLR FB pin?
The FB pin has a resistor to GND on 4 of 5 designs, most often 20 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the TPS62A02DRLR.
What parts are used alongside the TPS62A02DRLR?
The ADA4930-1YCPZ-R7, BUF802IRGTR, FIN1019MTCX, HMCAD1520 and LM27761DSGR appear in the most repositories here.
Which microcontrollers do boards using the TPS62A02DRLR use?
Most are built on FPGA (2), ESP32 (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the TPS62A02DRLR?
The median is 73 × 100 mm, and 0% are two-layer designs.
What is the most popular open source board using the TPS62A02DRLR?
By GitHub stars, Thunderscope Rev5.3 by EEVengers, with 1,336 stars.
Can I simulate one of these boards using the TPS62A02DRLR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.