6 open source boards using the TXS0108E
Real designs built with the TXS0108E, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FT81x Arduino Driver
blazer82
42.8 × 36.8 mm30 parts4LMIT58- schematic only · 15 partsESP32
RV8
JOJOCAFE
15 partsNo license1 RP2040/RP2350
Robot link
sequoia-hope
28 × 63 mm93 parts6LNo license0Dlr carrier
arcnode-io
120 × 105 mm89 parts4LNo license0NXP
Teensyv
english1234
100 × 100 mm74 parts2LGPL-2.068AVR/Arduino
ReflowOvenController
wangyeee
100 × 100 mm97 parts2LBSD-3-Clause9
How designs wire the TXS0108E
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TXS0108E connects to, and the resistors, capacitors and other passives placed on it.
- Pin 11 is tied to GND on 5 of 5 designs.
- Pin 10 has a resistor to GND on 4 of 5 designs, most often 1 kΩ (then 100 kΩ).
- Pin 2 is tied to 1.8V on 4 of 5 designs.
- Pin 19 is tied to 3.3V on 4 of 5 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 2 | Connected to: 1.8V 80% · not connected 20% |
|
| Pin 10 | Connected to: A connector 40%, the microcontroller 40% · 3V 20% |
|
| Pin 11 | Connected to: GND 100% | — |
| Pin 19 | Connected to: 3.3V 80% · not connected 20% |
|
16 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Teensyv by english1234, FT81x Arduino Driver by blazer82, ReflowOvenController by wangyeee and Dlr carrier by arcnode-io.
The TXS0108E in open source designs
The gallery holds 6 open source boards using the TXS0108E from 6 GitHub repositories; a typical one measures about 100 × 100 mm and carries around 82 components.
60% use four copper layers or more, and 50% carry an open source license.
The most starred is Teensyv by english1234.
Microcontrollers on boards using the TXS0108E
What boards using the TXS0108E are built for
TXS0108E: common questions
Where can I find a TXS0108E reference design?
Each of the 6 boards on this page is a real design using the TXS0108E. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TXS0108E pin 11 connected?
Pin 11 is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TXS0108E.
What resistor goes on the TXS0108E pin 10?
Pin 10 has a resistor to GND on 4 of 5 designs, most often 1 kΩ (then 100 kΩ). Counted from the KiCad layouts of 5 open source designs using the TXS0108E.
How is the TXS0108E pin 2 connected?
Pin 2 is tied to 1.8V on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TXS0108E.
Which microcontrollers do boards using the TXS0108E use?
Most are built on AVR/Arduino (1), ESP32 (1), NXP (1) and RP2040/RP2350 (1).
How big is a typical board using the TXS0108E?
The median is 100 × 100 mm, and 40% are two-layer designs.
What is the most popular open source board using the TXS0108E?
By GitHub stars, Teensyv by english1234, with 68 stars.
Can I simulate one of these boards using the TXS0108E before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.