8 open source boards using the USB3343

Real designs built with the USB3343, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

8 boardsClear filters|Most starred

How designs wire the USB3343

Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the USB3343 connects to, and the resistors, capacitors and other passives placed on it.

  • The VDDIO pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 1 µF).
  • The VDD33 pin has a capacitor to GND on 6 of 6 designs, most often 1 µF (then 2.2 µF).
  • The VBAT pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 1 µF).
  • The RBIAS pin has a resistor to GND on 6 of 6 designs, most often 8.06 kΩ.
VDDIOpin 9Connected to: 3.3V 100%
  • Decoupling capacitor on 100% · 100 nF (7), 1 µF (3)
VDD33pin 15Connected to: Signal 67% · VDD33 33%
  • Capacitor to GND on 100% · 1 µF (4), 2.2 µF (1), 100 nF (1)
VBATpin 16Connected to: 3.3V 100%
  • Decoupling capacitor on 100% · 100 nF (7), 1 µF (2)
VBUSpin 17Connected to: Signal 83% · VBUS 17%
  • Series resistor on 67% · 20 kΩ (3), 10 kΩ (1)
IDpin 18Connected to: VDD33 50% · a signal 50%
  • Capacitor to GND on 83% · 1 µF (2), 100 nF (2), 2.2 µF (1)
RBIASpin 19Connected to: Signal 100%
  • Resistor to GND on 100% · 8.06 kΩ (6)
XOpin 20Connected to: Not connected 67% · a signal 33%
  • Series resistor on 33% · 1 MΩ (2)
  • Crystal on 33% · 26 MHz (1)
  • Capacitor to GND on 33% · 4.3 pF (1), 3 pF (1)
REFCLK/XIpin 21Connected to: Signal 100%
  • Series resistor on 67% · 1 MΩ (2), 100 Ω (1), 0 Ω (1)
  • Crystal on 50% · 26 MHz (2)
  • Capacitor to GND on 33% · 4.3 pF (1), 3 pF (1)
RESETBpin 22Connected to: The microcontroller 50%
  • Pull-up to 3.3V on 50% · 10 kΩ (3)
VDD18pin 23Connected to: Signal 67% · 1.8V 33%
  • Capacitor to GND on 100% · 1 µF (4), 100 nF (2), 2.2 µF (1)
GNDpin 25Connected to: GND 100%

14 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Usb sniffer by ataradov, USB Dongle KiCad by 2sayle, Dalishen pi h7p20 by vllogic and Replicookie by cmcquinn.

The USB3343 in open source designs

The gallery holds 8 open source boards using the USB3343 from 6 GitHub repositories; a typical one measures about 64.1 × 47.8 mm and carries around 139 components.

88% use four copper layers or more, and 38% carry an open source license.

The most starred is Usb sniffer by ataradov.

Microcontrollers on boards using the USB3343

What boards using the USB3343 are built for

USB3343: common questions

Where can I find a USB3343 reference design?

Each of the 8 boards on this page is a real design using the USB3343. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the USB3343 VDDIO pin?

The VDDIO pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the USB3343.

How is the USB3343 VDD33 pin connected?

The VDD33 pin has a capacitor to GND on 6 of 6 designs, most often 1 µF (then 2.2 µF). Counted from the KiCad layouts of 6 open source designs using the USB3343.

What decoupling capacitors do designs use on the USB3343 VBAT pin?

The VBAT pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 6 open source designs using the USB3343.

Which microcontrollers do boards using the USB3343 use?

Most are built on ESP32 (1), FPGA (1), Microchip SAM (1) and STM32 (1).

How big is a typical board using the USB3343?

The median is 64.1 × 47.8 mm, and 13% are two-layer designs.

What is the most popular open source board using the USB3343?

By GitHub stars, Usb sniffer by ataradov, with 1,281 stars.

Can I simulate one of these boards using the USB3343 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part