5 open source boards using the USBULC6-2M6

Real designs built with the USBULC6-2M6, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the USBULC6-2M6

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the USBULC6-2M6 connects to, and the resistors, capacitors and other passives placed on it.

  • The 2 pin is tied to GND on 5 of 5 designs.
  • The 5 pin has a ferrite bead on 3 of 5 designs, most often 1 kH.
  • The 5 pin is tied to 5V on 3 of 5 designs (a signal on 2).
2pin 2Connected to: GND 100%
5pin 5Connected to: 5V 60% · a signal 40%
  • Ferrite bead on 60% · 1 kH (1)

4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include MobilECG main by peterisza, USB Dongle KiCad by 2sayle, Integrated Debugger by PicoballoonLabs and Signet hc pcb by nthdimtech.

The USBULC6-2M6 in open source designs

The gallery holds 5 open source boards using the USBULC6-2M6 from 5 GitHub repositories; a typical one measures about 30 × 28.4 mm and carries around 72 components.

100% use four copper layers or more, and 60% carry an open source license.

The most starred is MobilECG main by peterisza.

Microcontrollers on boards using the USBULC6-2M6

What boards using the USBULC6-2M6 are built for

USBULC6-2M6: common questions

Where can I find a USBULC6-2M6 reference design?

Each of the 5 boards on this page is a real design using the USBULC6-2M6. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the USBULC6-2M6 2 pin connected?

The 2 pin is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the USBULC6-2M6.

How is the USBULC6-2M6 5 pin connected?

The 5 pin has a ferrite bead on 3 of 5 designs, most often 1 kH. Counted from the KiCad layouts of 5 open source designs using the USBULC6-2M6.

What parts are used alongside the USBULC6-2M6?

The 256kx8, ADS1298, ESD_PROTECTOR, LIS2DH12 and OPA379 appear in the most repositories here.

Which microcontrollers do boards using the USBULC6-2M6 use?

Most are built on STM32 (5).

How big is a typical board using the USBULC6-2M6?

The median is 30 × 28.4 mm, and 0% are two-layer designs.

What is the most popular open source board using the USBULC6-2M6?

By GitHub stars, MobilECG main by peterisza, with 66 stars.

Can I simulate one of these boards using the USBULC6-2M6 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part