11 open source boards using the W25Q128JVSIQ TR
Real designs built with the W25Q128JVSIQ TR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Obsidian boa r0.1
silvioviscuso
35.6 × 17.8 mm71 parts4LNo license10RP2040/RP2350
BMS
AerospaceNU
100 × 100 mm342 parts6LNo license4Raspberry Pi
Usb3.1-Ethernet-RP2040-I2S HUB
Tanawin1701d
100 × 100 mm136 parts4LNo license1RP2040/RP2350
RP2040-Embedded-Controller
0susi0
145 × 75 mm47 parts2LMIT1FPGA
FPL
jacobjuneau6
100 × 100 mm134 parts2LMIT0RP2040/RP2350
Simple-FC
someonelse20
40 × 40 mm72 parts4LMIT0RP2040/RP2350
TimeCapsule
jaxfry
50 × 70 mm51 parts2LNo license0ESP32
V1
silvioviscuso
35.6 × 17.8 mm67 parts4LNo license10STM32
Fc
cookiemonsternz
28.3 × 28.3 mm72 parts6LNo license5FPGA
FPL marked
jacobjuneau6
100 × 99.8 mm60 parts4LMIT0ESP32
V9
silvioviscuso
35.6 × 17.8 mm62 parts4LNo license10
How designs wire the W25Q128JVSIQ TR
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the W25Q128JVSIQ TR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 10 µF).
- The CS pin has a series resistor on 5 of 8 designs, most often 1 kΩ (then 10 kΩ).
- The CS pin has a pull-up to 3.3V on 4 of 8 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CSpin 1 | Connected to: The microcontroller 75%, SC0914(13) 25% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| VCCpin 8 | Connected to: 3.3V 100% |
|
5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Obsidian boa r0.1 by silvioviscuso, Fc by cookiemonsternz, BMS by AerospaceNU and RP2040-Embedded-Controller by 0susi0.
The W25Q128JVSIQ TR in open source designs
The gallery holds 11 open source boards using the W25Q128JVSIQ TR from 8 GitHub repositories; a typical one measures about 50 × 70 mm and carries around 71 components.
73% use four copper layers or more, and 36% carry an open source license.
The most starred is Obsidian boa r0.1 by silvioviscuso.
Parts used alongside the W25Q128JVSIQ TR
Microcontrollers on boards using the W25Q128JVSIQ TR
What boards using the W25Q128JVSIQ TR are built for
W25Q128JVSIQ TR: common questions
Where can I find a W25Q128JVSIQ TR reference design?
Each of the 11 boards on this page is a real design using the W25Q128JVSIQ TR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the W25Q128JVSIQ TR VCC pin?
The VCC pin has a decoupling capacitor on 7 of 8 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 8 open source designs using the W25Q128JVSIQ TR.
What resistor goes on the W25Q128JVSIQ TR CS pin?
The CS pin has a series resistor on 5 of 8 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 8 open source designs using the W25Q128JVSIQ TR.
Which microcontrollers do boards using the W25Q128JVSIQ TR use?
Most are built on RP2040/RP2350 (4), ESP32 (3), FPGA (2) and Raspberry Pi (1).
How big is a typical board using the W25Q128JVSIQ TR?
The median is 50 × 70 mm, and 27% are two-layer designs.
What is the most popular open source board using the W25Q128JVSIQ TR?
By GitHub stars, Obsidian boa r0.1 by silvioviscuso, with 10 stars.
Can I simulate one of these boards using the W25Q128JVSIQ TR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.