6 open source boards using the W25Q32JVSNIQ
Real designs built with the W25Q32JVSNIQ, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Ice4pi
lightside-instruments
65 × 30 mm52 parts4LTAPR-OHL-1.08FPGA
Ice4pi
vlvassilev
65 × 30 mm52 parts4LTAPR-OHL-1.03STM32
Chronolog
slemanz
100 × 50 mm87 parts4LNo license2RP2040/RP2350
Avionics-Mainboard
cmu-argus-2
90.2 × 95.9 mm316 parts4LNo license1FPGA
Ice4pi gpib
lightside-instruments
85 × 56 mm94 parts4LTAPR-OHL-1.00ESP32
Esp32c6-pico
TreeNewbeer
18 × 29 mm59 parts4LNo license0
How designs wire the W25Q32JVSNIQ
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the W25Q32JVSNIQ connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 10 nF).
- The CS pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ.
- The WP pin has a pull-up to 3.3V on 3 of 6 designs, most often 10 kΩ.
- The SCK pin has a pull-up to 3.3V on 3 of 6 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CSpin 1 | Connected to: The microcontroller 67%, a connector 50% |
|
| WPpin 3 | Connected to: Signal 83% · 3.3V 17% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| SCKpin 6 | Connected to: The microcontroller 67%, a connector 50% |
|
| HOLDpin 7 | Connected to: Signal 83% · 3.3V 17% |
|
| VCCpin 8 | Connected to: 3.3V 100% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Ice4pi by lightside-instruments, Ice4pi by vlvassilev, Chronolog by slemanz and Avionics-Mainboard by cmu-argus-2.
The W25Q32JVSNIQ in open source designs
The gallery holds 6 open source boards using the W25Q32JVSNIQ from 6 GitHub repositories; a typical one measures about 75 × 40 mm and carries around 73 components.
100% use four copper layers or more, and 50% carry an open source license.
The most starred is Ice4pi by lightside-instruments.
Parts used alongside the W25Q32JVSNIQ
Microcontrollers on boards using the W25Q32JVSNIQ
What boards using the W25Q32JVSNIQ are built for
W25Q32JVSNIQ: common questions
Where can I find a W25Q32JVSNIQ reference design?
Each of the 6 boards on this page is a real design using the W25Q32JVSNIQ. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the W25Q32JVSNIQ VCC pin?
The VCC pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 6 open source designs using the W25Q32JVSNIQ.
What pull-up resistor is used on the W25Q32JVSNIQ CS pin?
The CS pin has a pull-up to 3.3V on 5 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the W25Q32JVSNIQ.
What pull-up resistor is used on the W25Q32JVSNIQ WP pin?
The WP pin has a pull-up to 3.3V on 3 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the W25Q32JVSNIQ.
What parts are used alongside the W25Q32JVSNIQ?
The DSC1001DI1-012.0000, ICE40HX1K-TQ144 and MIC5504-1.2YM5 appear in the most repositories here.
Which microcontrollers do boards using the W25Q32JVSNIQ use?
Most are built on FPGA (3), ESP32 (1), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the W25Q32JVSNIQ?
The median is 75 × 40 mm, and 0% are two-layer designs.
What is the most popular open source board using the W25Q32JVSNIQ?
By GitHub stars, Ice4pi by lightside-instruments, with 8 stars.
Can I simulate one of these boards using the W25Q32JVSNIQ before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.