12 open source boards using the WS2811
Real designs built with the WS2811, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Controller
candykingdom
150 × 68 mm190 parts2LNo license5- schematic only · 139 partsESP32
GrowHub
Ajakovski
139 partsMIT2 WS2811 LED Driver 24 (2 Signals)
jgraichen
140 × 25 mm16 parts2LCC-BY-SA-4.01STM32
ShroomShed MKII
OilyT
88 × 72 mm86 parts4LNo license0Cybr light blade
dsalaj
356 × 65 mm62 parts2LNo license0RISC-V
NoodleDriver
mcqn
36 × 70 mm41 parts2LCERN-OHL-S-2.00AVR/Arduino
RGB-LED-controller-
MohamedHassanExp
50.1 × 46 mm24 parts2LMIT0RGB 2x2 with WS2811
sullyjason
41.9 × 59.7 mm27 parts2LNo license1WS2811 LED Driver 12 (1 Signal)
jgraichen
140 × 25 mm12 parts2LCC-BY-SA-4.01WS2811 LED Driver 9LS (2 Lichtsperrsignal)
jgraichen
60 × 45 mm8 parts2LCC-BY-SA-4.01WS2811 LED Driver 6LS (1 Lichtsperrsignal)
jgraichen
60 × 45 mm7 parts2LCC-BY-SA-4.01Ws2811
Tert2
83 × 100 mm15 parts2LNo license0
How designs wire the WS2811
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the WS2811 connects to, and the resistors, capacitors and other passives placed on it.
- The VDD pin has a pull-up to BATT on 8 of 8 designs, most often 100 Ω (then 150 Ω).
- The VDD pin has a capacitor to GND on 7 of 8 designs, most often 100 nF (then 1 µF).
- The SET pin is left unconnected on 8 of 8 designs.
- The DIN pin has a series resistor on 6 of 8 designs, most often 33 Ω (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 4 | Connected to: GND 100% | — |
| DOpin 5 | Connected to: WS2811 38% |
|
| DINpin 6 | Connected to: Signal 100% |
|
| SETpin 7 | Connected to: Not connected 100% | — |
| VDDpin 8 | Connected to: Signal 100% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Controller by candykingdom, WS2811 LED Driver 12 (1 Signal) by jgraichen, RGB 2x2 with WS2811 by sullyjason and Cybr light blade by dsalaj.
The WS2811 in open source designs
The gallery holds 12 open source boards using the WS2811 from 9 GitHub repositories; a typical one measures about 83 × 59.7 mm and carries around 26 components.
91% are two-layer designs, the rest use four layers or more, and 58% carry an open source license.
The most starred is Controller by candykingdom.
Microcontrollers on boards using the WS2811
What boards using the WS2811 are built for
WS2811: common questions
Where can I find a WS2811 reference design?
Each of the 12 boards on this page is a real design using the WS2811. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the WS2811 VDD pin?
The VDD pin has a pull-up to BATT on 8 of 8 designs, most often 100 Ω (then 150 Ω). Counted from the KiCad layouts of 8 open source designs using the WS2811.
How is the WS2811 SET pin connected?
The SET pin is left unconnected on 8 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the WS2811.
What resistor goes on the WS2811 DIN pin?
The DIN pin has a series resistor on 6 of 8 designs, most often 33 Ω (then 10 kΩ). Counted from the KiCad layouts of 8 open source designs using the WS2811.
Which microcontrollers do boards using the WS2811 use?
Most are built on STM32 (2), AVR/Arduino (1), ESP32 (1) and RISC-V (1).
How big is a typical board using the WS2811?
The median is 83 × 59.7 mm, and 91% are two-layer designs.
What is the most popular open source board using the WS2811?
By GitHub stars, Controller by candykingdom, with 5 stars.
Can I simulate one of these boards using the WS2811 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.