8 open source boards using the WT32-ETH01
Real designs built with the WT32-ETH01, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Pcb ws2812-ethernet controller
klein0r
26.9 × 73.9 mm11 parts2LMIT38Lateral led controller
cyberboy666
100 × 60 mm30 parts2LGPL-3.081w-If
waldbaer
68 × 85 mm44 parts2LMIT0WT32-ETH01 PWM Fan Controller
Caroma97
84 × 57.8 mm17 parts2LMIT0ESP32
BoneIO - dimmer board 4x4A
boneIO-eu
67.8 × 86.9 mm106 parts2LGPL-3.02ESP32
MiAM SupervisorBoard
14chanwa
104.4 × 63.5 mm29 parts2LNo license0BoneIO - expansion module
boneIO-eu
86 × 74 mm74 parts2LGPL-3.02ESP32
Weather ESP32
computergeek1507
63.4 × 85 mm16 parts2LCERN-OHL-1.210
How designs wire the WT32-ETH01
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the WT32-ETH01 connects to, and the resistors, capacitors and other passives placed on it.
- The 5V pin is tied to 5V on 5 of 7 designs.
- The LINK pin is left unconnected on 5 of 6 designs.
- The 3V3 pins is tied to 3.3V on 69% of them (not connected on 2, a signal on 2).
- The IO14 pin has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2, 9, 11, 17, 26 | Connected to: GND 65% · not connected 23% | — |
| 3V3pin 3, 10 | Connected to: 3.3V 69% · not connected 15% · a signal 15% | — |
| 5Vpin 12 | Connected to: 5V 71% | — |
| LINKpin 13 | Connected to: Not connected 83% · GND 17% | — |
| IO14pin 21 | Connected to: A connector 29% |
|
15 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Pcb ws2812-ethernet controller by klein0r, Weather ESP32 by computergeek1507, Lateral led controller by cyberboy666 and BoneIO - dimmer board 4x4A by boneIO-eu.
The WT32-ETH01 in open source designs
The gallery holds 8 open source boards using the WT32-ETH01 from 7 GitHub repositories; a typical one measures about 76 × 74 mm and carries around 30 components.
100% are two-layer designs, the rest use four layers or more, and 88% carry an open source license.
The most starred is Pcb ws2812-ethernet controller by klein0r.
Microcontrollers on boards using the WT32-ETH01
What boards using the WT32-ETH01 are built for
WT32-ETH01: common questions
Where can I find a WT32-ETH01 reference design?
Each of the 8 boards on this page is a real design using the WT32-ETH01. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the WT32-ETH01 5V pin connected?
The 5V pin is tied to 5V on 5 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the WT32-ETH01.
How is the WT32-ETH01 LINK pin connected?
The LINK pin is left unconnected on 5 of 6 designs. Counted from the KiCad layouts of 7 open source designs using the WT32-ETH01.
How is the WT32-ETH01 3V3 pin connected?
The 3V3 pins is tied to 3.3V on 69% of them (not connected on 2, a signal on 2). Counted from the KiCad layouts of 7 open source designs using the WT32-ETH01.
Which microcontrollers do boards using the WT32-ETH01 use?
Most are built on ESP32 (3).
How big is a typical board using the WT32-ETH01?
The median is 76 × 74 mm, and 100% are two-layer designs.
What is the most popular open source board using the WT32-ETH01?
By GitHub stars, Pcb ws2812-ethernet controller by klein0r, with 38 stars.
Can I simulate one of these boards using the WT32-ETH01 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.