6 open source boards using the XL1509-ADJ
Real designs built with the XL1509-ADJ, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
XCKU5P-Development-Notes
sjbar03
191 × 125.5 mm96 parts2LNo license3STM32
Audio daughterboard
Jaxc
90 × 155 mm453 parts4LGPL-3.02RISC-V
Linkodrive08
jediminer543
67.2 × 90.4 mm144 parts4LApache-2.01STM32
XCS-03A-MAIN
hedong2023
153.6 × 50 mm242 parts2LNo license0FPGA
Eurorack-DIGI
cookiemonsternz
40 × 100 mm127 parts6LNo license0Edf esc
iamdarshg
98 × 58 mm74 parts4LMIT0
How designs wire the XL1509-ADJ
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the XL1509-ADJ connects to, and the resistors, capacitors and other passives placed on it.
- The EN pin is tied to GND on 6 of 6 designs.
- The OUT pin has a inductor on 4 of 6 designs, most often 47 µH (then 22 µH).
- The FB pin has a resistor to GND on 4 of 6 designs, most often 1 kΩ (then 20 kΩ).
- The FB pin has a pull-up to 3.3V on 3 of 6 designs, most often 33 kΩ (then 470 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VIN_1pin 1 | Connected to: VDD 67% · a signal 33% |
|
| OUTpin 2 | Connected to: Signal 83% · 12V 17% |
|
| FBpin 3 | Connected to: Signal 83% · 12V 17% |
|
| ENpin 4 | Connected to: GND 100% | — |
| GND_5pin 5 | Connected to: GND 67% · not connected 17% · a signal 17% | — |
| GND_6pin 6 | Connected to: GND 67% · a signal 33% | — |
| GND_7pin 7 | Connected to: GND 67% · a signal 33% | — |
| GND_8pin 8 | Connected to: GND 67% · not connected 17% · a signal 17% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include XCKU5P-Development-Notes by sjbar03, Audio daughterboard by Jaxc, Linkodrive08 by jediminer543 and Eurorack-DIGI by cookiemonsternz.
The XL1509-ADJ in open source designs
The gallery holds 6 open source boards using the XL1509-ADJ from 6 GitHub repositories; a typical one measures about 94 × 95.2 mm and carries around 136 components.
67% use four copper layers or more, and 50% carry an open source license.
The most starred is XCKU5P-Development-Notes by sjbar03.
Parts used alongside the XL1509-ADJ
What boards using the XL1509-ADJ are built for
XL1509-ADJ: common questions
Where can I find a XL1509-ADJ reference design?
Each of the 6 boards on this page is a real design using the XL1509-ADJ. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the XL1509-ADJ EN pin connected?
The EN pin is tied to GND on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the XL1509-ADJ.
How is the XL1509-ADJ OUT pin connected?
The OUT pin has a inductor on 4 of 6 designs, most often 47 µH (then 22 µH). Counted from the KiCad layouts of 6 open source designs using the XL1509-ADJ.
What resistor goes on the XL1509-ADJ FB pin?
The FB pin has a resistor to GND on 4 of 6 designs, most often 1 kΩ (then 20 kΩ). Counted from the KiCad layouts of 6 open source designs using the XL1509-ADJ.
Which microcontrollers do boards using the XL1509-ADJ use?
Most are built on STM32 (2), FPGA (1) and RISC-V (1).
How big is a typical board using the XL1509-ADJ?
The median is 94 × 95.2 mm, and 33% are two-layer designs.
What is the most popular open source board using the XL1509-ADJ?
By GitHub stars, XCKU5P-Development-Notes by sjbar03, with 3 stars.
Can I simulate one of these boards using the XL1509-ADJ before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.