6 open source boards using the 6N139
Real designs built with the 6N139, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
OpenEuroBoard
sensai7
300 × 100 mm135 parts2LGPL-3.041TI MSP430/CC
CCVDrum
sensai7
106 × 54.5 mm38 parts2LMIT14YM3812-dual synth
89Mods
99.8 × 44.2 mm40 parts4LApache-2.01ESP32
BarSync
barna81
95 × 60 mm16 parts2LCC-BY-NC-4.01Cdipannoucer
buelowp
105.7 × 60.2 mm53 parts2LMIT0Med assoc lick sens addon
Sussex-Neuroscience
50.8 × 52.1 mm11 parts2LGPL-3.01
How designs wire the 6N139
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the 6N139 connects to, and the resistors, capacitors and other passives placed on it.
- The C1 pin has a series resistor on 5 of 6 designs, most often 220 Ω (then 4.3 kΩ).
- The VO2 pin has a pull-up to 5V on 5 of 6 designs, most often 270 Ω (then 220 Ω).
- The VO1 pin is left unconnected on 5 of 6 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| NCpin 1, 4 | Connected to: Not connected 100% | — |
| C1pin 2 | Connected to: Signal 100% |
|
| GNDpin 5 | Connected to: GND 83% · a signal 17% | — |
| VO2pin 6 | Connected to: The microcontroller 33% |
|
| VO1pin 7 | Connected to: Not connected 83% · a signal 17% | — |
| VCCpin 8 | Connected to: 5V 67% · a signal 33% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include OpenEuroBoard by sensai7, CCVDrum by sensai7, YM3812-dual synth by 89Mods and BarSync by barna81.
The 6N139 in open source designs
The gallery holds 6 open source boards using the 6N139 from 6 GitHub repositories; a typical one measures about 102.8 × 57.3 mm and carries around 39 components.
83% are two-layer designs, the rest use four layers or more, and 83% carry an open source license.
The most starred is OpenEuroBoard by sensai7.
Microcontrollers on boards using the 6N139
What boards using the 6N139 are built for
6N139: common questions
Where can I find a 6N139 reference design?
Each of the 6 boards on this page is a real design using the 6N139. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the 6N139 C1 pin?
The C1 pin has a series resistor on 5 of 6 designs, most often 220 Ω (then 4.3 kΩ). Counted from the KiCad layouts of 6 open source designs using the 6N139.
What pull-up resistor is used on the 6N139 VO2 pin?
The VO2 pin has a pull-up to 5V on 5 of 6 designs, most often 270 Ω (then 220 Ω). Counted from the KiCad layouts of 6 open source designs using the 6N139.
How is the 6N139 VO1 pin connected?
The VO1 pin is left unconnected on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the 6N139.
Which microcontrollers do boards using the 6N139 use?
Most are built on ESP32 (1) and TI MSP430/CC (1).
How big is a typical board using the 6N139?
The median is 102.8 × 57.3 mm, and 83% are two-layer designs.
What is the most popular open source board using the 6N139?
By GitHub stars, OpenEuroBoard by sensai7, with 41 stars.
Can I simulate one of these boards using the 6N139 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.