15 open source boards using the 74AHCT595
Real designs built with the 74AHCT595, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
DevRamCart RevA
Danjovic
100 × 64.7 mm37 parts2LGPL-2.043Ym2610
dan-rodrigues
100.9 × 77.5 mm157 parts4LNo license29ESP32
Esp32PrinterController
MitchBradley
157.5 × 97.8 mm70 parts2LMIT16RP2040/RP2350
Mainboard
mincrmatt12
136.3 × 71.1 mm160 parts4LMIT11NXP
Spdif decoder
maddoxlab
92.7 × 96.5 mm28 parts2LBSD-3-Clause2Nordic nRF
WatchEMS
humancomputerintegration
105.4 × 25.4 mm131 parts2LNo license0GP8B
JonathSpirit
133 × 93 mm105 parts4LCERN-OHL-W-2.00Carte mère V2
MathysPelletier
180.1 × 91.5 mm97 parts2LNo license0NXP
Modulation dependent carrier level
frohro
220 × 233 mm64 parts4LGPL-3.00AVR/Arduino
HKN-BetaPsi-DIY-Watch-Kit
jamusix99
49.6 × 66 mm21 parts2LNo license0Arm v3
evezor
250.2 × 63.3 mm100 parts4LCERN-OHL-P-2.0126ESP32
DevRam
Danjovic
100 × 64.7 mm36 parts2LGPL-2.043ESP32
ThePlatform MothedahFarm V2.0
AbdELRahmanGamiel
597.6 × 197.2 mm243 parts2LNo license0MusicBrain MATRIX - 8-stemmige audio patchmatrix
MarkWestbroek
175 × 142 mm63 parts4LMIT0Musicbrain matrix c
MarkWestbroek
154 × 133 mm63 parts4LMIT0
How designs wire the 74AHCT595
Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the 74AHCT595 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 9 of 13 designs, most often 100 nF (then 10 nF).
- The SRCLR pin is tied to 5V on 9 of 13 designs (a signal on 4).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 8 | Connected to: GND 92% | — |
| SRCLRpin 10 | Connected to: 5V 69% · a signal 31% | — |
| VCCpin 16 | Connected to: 5V 85% · a signal 15% |
|
13 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Arm v3 by evezor, DevRam by Danjovic, Ym2610-pcb by dan-rodrigues and Esp32PrinterController by MitchBradley.
The 74AHCT595 in open source designs
The gallery holds 15 open source boards using the 74AHCT595 from 13 GitHub repositories; a typical one measures about 136.3 × 91.5 mm and carries around 70 components.
53% are two-layer designs, the rest use four layers or more, and 67% carry an open source license.
The most starred is Arm v3 by evezor.
Parts used alongside the 74AHCT595
Microcontrollers on boards using the 74AHCT595
What boards using the 74AHCT595 are built for
74AHCT595: common questions
Where can I find a 74AHCT595 reference design?
Each of the 15 boards on this page is a real design using the 74AHCT595. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the 74AHCT595 VCC pin?
The VCC pin has a decoupling capacitor on 9 of 13 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 13 open source designs using the 74AHCT595.
How is the 74AHCT595 SRCLR pin connected?
The SRCLR pin is tied to 5V on 9 of 13 designs (a signal on 4). Counted from the KiCad layouts of 13 open source designs using the 74AHCT595.
What parts are used alongside the 74AHCT595?
The 74LVC1G34, AMS1117-3.3 and ULN2803A appear in the most repositories here.
Which microcontrollers do boards using the 74AHCT595 use?
Most are built on ESP32 (4), NXP (2), AVR/Arduino (1) and Nordic nRF (1).
How big is a typical board using the 74AHCT595?
The median is 136.3 × 91.5 mm, and 53% are two-layer designs.
What is the most popular open source board using the 74AHCT595?
By GitHub stars, Arm v3 by evezor, with 126 stars.
Can I simulate one of these boards using the 74AHCT595 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.