7 open source boards using the AD8606ARZ

Real designs built with the AD8606ARZ, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

7 boardsClear filters|Most starred

How designs wire the AD8606ARZ

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the AD8606ARZ connects to, and the resistors, capacitors and other passives placed on it.

  • The -INA_2 pin has a series resistor on 3 of 5 designs, most often 10 Ω (then 20 kΩ).
  • The +INA_3 pin has a series resistor on 3 of 5 designs, most often 13 kΩ (then 10 kΩ).
  • The V-_4 pin is tied to GND on 3 of 5 designs.
  • The OUTA_1 pin has a series resistor on 2 of 5 designs, most often 10 Ω (then 100 Ω).
OUTA_1pin 1Connected to: Signal 80% · not connected 20%
  • Series resistor on 40% · 10 Ω (1), 100 Ω (1)
  • Series capacitor on 40% · 470 nF (1), 470 pF (1), 47 µF (1)
-INA_2pin 2Connected to: Signal 100%
  • Series resistor on 60% · 10 Ω (1), 20 kΩ (1), 10 kΩ (1)
+INA_3pin 3Connected to: Signal 100%
  • Series resistor on 60% · 13 kΩ (1), 10 kΩ (1), 4.75 kΩ (1)
  • Capacitor to GND on 40% · 100 nF (1), 150 pF (1)
  • Resistor to GND on 40% · 200 kΩ (1), 20 kΩ (1)
V-_4pin 4Connected to: GND 60% · not connected 20% · a signal 20%
NCpin 5Connected to: Not connected 60% · a signal 40%
  • Series resistor on 40% · 100 kΩ (1), 4.75 kΩ (1)
-_6pin 6Connected to: Signal 60% · not connected 40%
  • Series resistor on 40% · 22 kΩ (1), 10 kΩ (1), 100 kΩ (1)
  • Series capacitor on 40% · 10 µF (1), 47 µF (1), 470 pF (1)
V+pin 7Connected to: Not connected 40% · 3.3V 20% · a signal 40%
  • Series capacitor on 40% · 10 µF (1), 47 µF (1), 470 pF (1)
V+_8pin 8Connected to: 3.3V 60% · not connected 40%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include UECG rev4 by ultimaterobotics, SIGNAL by Oerdna, FPCB by Kiya86 and EEE3088F Project by Mphoentle1.

The AD8606ARZ in open source designs

The gallery holds 7 open source boards using the AD8606ARZ from 5 GitHub repositories; a typical one measures about 80 × 70 mm and carries around 69 components.

71% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.

The most starred is UECG rev4 by ultimaterobotics.

Microcontrollers on boards using the AD8606ARZ

AD8606ARZ: common questions

Where can I find a AD8606ARZ reference design?

Each of the 7 boards on this page is a real design using the AD8606ARZ. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the AD8606ARZ -INA_2 pin?

The -INA_2 pin has a series resistor on 3 of 5 designs, most often 10 Ω (then 20 kΩ). Counted from the KiCad layouts of 5 open source designs using the AD8606ARZ.

What resistor goes on the AD8606ARZ +INA_3 pin?

The +INA_3 pin has a series resistor on 3 of 5 designs, most often 13 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the AD8606ARZ.

How is the AD8606ARZ V-_4 pin connected?

The V-_4 pin is tied to GND on 3 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the AD8606ARZ.

Which microcontrollers do boards using the AD8606ARZ use?

Most are built on AVR/Arduino (2), STM32 (2), ESP32 (1) and Nordic nRF (1).

How big is a typical board using the AD8606ARZ?

The median is 80 × 70 mm, and 71% are two-layer designs.

What is the most popular open source board using the AD8606ARZ?

By GitHub stars, UECG rev4 by ultimaterobotics, with 77 stars.

Can I simulate one of these boards using the AD8606ARZ before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part