11 open source boards using the ADS1015IDGSR
Real designs built with the ADS1015IDGSR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Labio
rishabh110493
152 × 85 mm234 parts2LNo license1ESP32
MPE HUB
felixmanfredi
117 × 107 mm235 parts4LNo license0RP2040/RP2350
OMiGaS
XiaotianGuan
92 × 44 mm120 parts4LNo license0ESP32
Acculux device
jjhcwoo
90 × 50 mm90 parts4LNo license0Bottom Board
avnguyen08
74.8 × 84.5 mm56 parts2LNo license0ESP32
AirQuality
leslier7
100 × 75 mm50 parts2LNo license0Controller board
raffcorreia
55 × 40 mm35 parts2LMIT0LiBo BaseBoard
ItsNotDaan
92.4 × 96.6 mm54 parts2LCERN-OHL-P-2.08Softgalaxy Pi HAT 2v0
hsclouds
69.1 × 60.8 mm57 parts2LNo license1ESP32
FCCU-v2-schematic
HydrogreenPollub
100 × 100 mm213 parts2LMIT0Esphome rgbcct led controller expansion
mikelawrence
41.5 × 20.5 mm19 parts2LCERN-OHL-P-2.01
How designs wire the ADS1015IDGSR
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the ADS1015IDGSR connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 9 of 10 designs, most often 10 kΩ (then 2 kΩ).
- The SCL pin has a pull-up to 3.3V on 9 of 10 designs, most often 10 kΩ (then 2 kΩ).
- The VDD pin has a decoupling capacitor on 7 of 10 designs, most often 100 nF (then 10 µF).
- The ALERT/RDY pin has a pull-up to 3.3V on 6 of 10 designs, most often 10 kΩ (then 2 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| ALERT/RDYpin 2 | Connected to: A connector 20%, the microcontroller 20% · not connected 20% |
|
| GNDpin 3 | Connected to: GND 100% | — |
| AIN0pin 4 | Connected to: A connector 40% |
|
| AIN1pin 5 | Connected to: A connector 40% |
|
| AIN2pin 6 | Connected to: A connector 40% · not connected 20% |
|
| VDDpin 8 | Connected to: 3.3V 100% |
|
| SDApin 9 | Connected to: A connector 40%, the microcontroller 40% |
|
| SCLpin 10 | Connected to: A connector 40%, the microcontroller 40% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include LiBo BaseBoard by ItsNotDaan, Softgalaxy Pi HAT 2v0 by hsclouds, Esphome rgbcct led controller expansion by mikelawrence and Labio by rishabh110493.
The ADS1015IDGSR in open source designs
The gallery holds 11 open source boards using the ADS1015IDGSR from 11 GitHub repositories; a typical one measures about 92 × 75 mm and carries around 57 components.
73% are two-layer designs, the rest use four layers or more, and 36% carry an open source license.
The most starred is LiBo BaseBoard by ItsNotDaan.
Parts used alongside the ADS1015IDGSR
Microcontrollers on boards using the ADS1015IDGSR
What boards using the ADS1015IDGSR are built for
ADS1015IDGSR: common questions
Where can I find a ADS1015IDGSR reference design?
Each of the 11 boards on this page is a real design using the ADS1015IDGSR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ADS1015IDGSR SDA pin?
The SDA pin has a pull-up to 3.3V on 9 of 10 designs, most often 10 kΩ (then 2 kΩ). Counted from the KiCad layouts of 10 open source designs using the ADS1015IDGSR.
What pull-up resistor is used on the ADS1015IDGSR SCL pin?
The SCL pin has a pull-up to 3.3V on 9 of 10 designs, most often 10 kΩ (then 2 kΩ). Counted from the KiCad layouts of 10 open source designs using the ADS1015IDGSR.
What decoupling capacitors do designs use on the ADS1015IDGSR VDD pin?
The VDD pin has a decoupling capacitor on 7 of 10 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 10 open source designs using the ADS1015IDGSR.
Which microcontrollers do boards using the ADS1015IDGSR use?
Most are built on ESP32 (4) and RP2040/RP2350 (1).
How big is a typical board using the ADS1015IDGSR?
The median is 92 × 75 mm, and 73% are two-layer designs.
What is the most popular open source board using the ADS1015IDGSR?
By GitHub stars, LiBo BaseBoard by ItsNotDaan, with 8 stars.
Can I simulate one of these boards using the ADS1015IDGSR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.