11 open source boards using the AP22652W6-7
Real designs built with the AP22652W6-7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
FPGA
Hackrf pro
greatscottgadgets
120 × 75 mm503 parts6LCERN-OHL-P-2.063Nordic nRF
M2-smart iot module
antmicro
80.2 × 22.2 mm210 parts4LApache-2.030RP2040/RP2350
HALPI2-hardware
hatlabs
187 × 109 mm541 parts6LCustom license9RP2040/RP2350
Audio latency tester board
antmicro
80 × 40 mm201 parts4LApache-2.01ESP32
SlimeVR Dock
Skaut0071
100 × 78 mm151 parts2LCERN-OHL-P-2.01PIC
BMS 02
Voltworks-Garage
96.7 × 175.6 mm614 parts4LGPL-3.00ESP32
Capable jetson carrier
CapableRobot
100 × 55 mm344 parts6LApache-2.00PIC
BMS 01
Voltworks-Garage
96.7 × 175.7 mm598 parts4LGPL-3.00ESP32
CRMHJN capable carrier
CapableRobot
122 × 77 mm344 parts6LApache-2.00PIC
BodyController 01
Voltworks-Garage
155 × 106 mm398 parts4LGPL-3.00PIC
DCDC 01
Voltworks-Garage
150.2 × 127.1 mm204 parts2LGPL-3.00
How designs wire the AP22652W6-7
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the AP22652W6-7 connects to, and the resistors, capacitors and other passives placed on it.
- The ILIM pin has a resistor to GND on 7 of 7 designs, most often 180 kΩ (then 27 kΩ).
- The EN pin has a series resistor on 3 of 7 designs, most often 10 kΩ.
- The EN pin has a resistor to GND on 3 of 7 designs, most often 100 kΩ.
- The EN pin has a pull-up to 5V on 3 of 7 designs, most often 10 kΩ (then 100 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 2 | Connected to: GND 100% | — |
| ENpin 3 | Connected to: Signal 86% |
|
| FAULTpin 4 | Connected to: Signal 57% · not connected 29% |
|
| ILIMpin 5 | Connected to: Signal 100% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hackrf pro by greatscottgadgets, M2-smart iot module by antmicro, HALPI2-hardware by hatlabs and Audio latency tester board by antmicro.
The AP22652W6-7 in open source designs
The gallery holds 11 open source boards using the AP22652W6-7 from 7 GitHub repositories; a typical one measures about 100 × 78 mm and carries around 344 components.
82% use four copper layers or more, and 91% carry an open source license.
The most starred is Hackrf pro by greatscottgadgets.
Parts used alongside the AP22652W6-7
Microcontrollers on boards using the AP22652W6-7
What boards using the AP22652W6-7 are built for
AP22652W6-7: common questions
Where can I find a AP22652W6-7 reference design?
Each of the 11 boards on this page is a real design using the AP22652W6-7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the AP22652W6-7 ILIM pin?
The ILIM pin has a resistor to GND on 7 of 7 designs, most often 180 kΩ (then 27 kΩ). Counted from the KiCad layouts of 7 open source designs using the AP22652W6-7.
What resistor goes on the AP22652W6-7 EN pin?
The EN pin has a series resistor on 3 of 7 designs, most often 10 kΩ. Counted from the KiCad layouts of 7 open source designs using the AP22652W6-7.
What pull-up resistor is used on the AP22652W6-7 FAULT pin?
The FAULT pin has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ. Counted from the KiCad layouts of 7 open source designs using the AP22652W6-7.
Which microcontrollers do boards using the AP22652W6-7 use?
Most are built on PIC (4), ESP32 (3), RP2040/RP2350 (2) and FPGA (1).
How big is a typical board using the AP22652W6-7?
The median is 100 × 78 mm, and 18% are two-layer designs.
What is the most popular open source board using the AP22652W6-7?
By GitHub stars, Hackrf pro by greatscottgadgets, with 63 stars.
Can I simulate one of these boards using the AP22652W6-7 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.