12 open source boards using the AP3012
Real designs built with the AP3012, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
SenseEHajo
ehajo
141 × 56.9 mm97 parts2LNo license5ESP32
MinRead
Monacrylic
64.5 × 120.5 mm114 parts2LNo license2STM32
SparkFun Qwiic WAV Trigger Pro
sparkfun
44.5 × 38.1 mm97 parts2LNo license2AVR/Arduino
Mss cascade adv
IowaScaledEngineering
127 × 76.2 mm134 parts2LNo license0STM32
Sipm
npgo22
45 × 45 mm67 parts4LNo license0RP2040/RP2350
LoopingBrummes
PfadGetreide
91.4 × 70.5 mm20 parts2LNo license0FPGA
BosonFrameGrabber
gregdavill
63 × 63 mm64 parts4LMIT38ESP32
X de link
Monacrylic
64.5 × 120.5 mm114 parts2LNo license2STM32
SparkFun Qwiic WAV Trigger Pro panelized
sparkfun
148.1 × 134.1 mm97 parts2LNo license2AVR/Arduino
Mss cascade basic
IowaScaledEngineering
82.6 × 76.2 mm85 parts2LNo license0LCD-Fixup
cscott
25.5 × 30.5 mm17 parts2LNo license0NXP
JABICAN-USB Pro
dragonlock2
70.3 × 38 mm91 parts2LApache-2.013
How designs wire the AP3012
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the AP3012 connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 9 of 9 designs, most often 10 µH (then 4.7 µH).
- The FB pin has a resistor to GND on 7 of 9 designs, most often 10 kΩ (then 5.1 kΩ).
- The IN pin has a inductor on 7 of 9 designs, most often 10 µH (then 1 µH).
- The FB pin has a series resistor on 6 of 9 designs, most often 10 kΩ (then 22 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SWpin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 89% | — |
| FBpin 3 | Connected to: Signal 100% |
|
| SHDNpin 4 | Connected to: 5V 56% · a signal 44% |
|
| INpin 5 | Connected to: 5V 67% · a signal 33% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include BosonFrameGrabber by gregdavill, JABICAN-USB Pro by dragonlock2, SenseEHajo by ehajo and MinRead pcb by Monacrylic.
The AP3012 in open source designs
The gallery holds 12 open source boards using the AP3012 from 9 GitHub repositories; a typical one measures about 67.4 × 66.7 mm and carries around 94 components.
83% are two-layer designs, the rest use four layers or more, and 17% carry an open source license.
The most starred is BosonFrameGrabber by gregdavill.
Parts used alongside the AP3012
Microcontrollers on boards using the AP3012
What boards using the AP3012 are built for
AP3012: common questions
Where can I find a AP3012 reference design?
Each of the 12 boards on this page is a real design using the AP3012. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the AP3012 SW pin connected?
The SW pin has a inductor on 9 of 9 designs, most often 10 µH (then 4.7 µH). Counted from the KiCad layouts of 9 open source designs using the AP3012.
What resistor goes on the AP3012 FB pin?
The FB pin has a resistor to GND on 7 of 9 designs, most often 10 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 9 open source designs using the AP3012.
How is the AP3012 IN pin connected?
The IN pin has a inductor on 7 of 9 designs, most often 10 µH (then 1 µH). Counted from the KiCad layouts of 9 open source designs using the AP3012.
Which microcontrollers do boards using the AP3012 use?
Most are built on ESP32 (3), STM32 (3), AVR/Arduino (2) and FPGA (1).
How big is a typical board using the AP3012?
The median is 67.4 × 66.7 mm, and 83% are two-layer designs.
What is the most popular open source board using the AP3012?
By GitHub stars, BosonFrameGrabber by gregdavill, with 38 stars.
Can I simulate one of these boards using the AP3012 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.