5 open source boards using the AP63300WU-7

Real designs built with the AP63300WU-7, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the AP63300WU-7

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the AP63300WU-7 connects to, and the resistors, capacitors and other passives placed on it.

  • The VIN pin has a decoupling capacitor on 5 of 5 designs, most often 10 µF (then 100 nF).
  • The SW_5 pin has a inductor on 5 of 5 designs, most often 6.8 µH (then 47 µH).
  • The SW_5 pin has a series capacitor on 5 of 5 designs, most often 100 nF.
  • The BST_6 pin has a series capacitor on 5 of 5 designs, most often 100 nF.
FB_1pin 1Connected to: Signal 80% · 5V 20%
  • Resistor to GND on 80% · 30.1 kΩ (2), 4.3 kΩ (1), 10 kΩ (1)
  • Pull-up to 5V on 80% · 20 kΩ (1), 93.1 kΩ (1), 158 kΩ (1)
  • Capacitor to the supply on 40% · 56 pF (1), 47 pF (1)
EN_2pin 2Connected to: VDD 60% · a signal 40%
VINpin 3Connected to: VDD 80% · a signal 20%
  • Decoupling capacitor on 100% · 10 µF (6), 100 nF (2)
GND_4pin 4Connected to: GND 100%
SW_5pin 5Connected to: Signal 100%
  • Inductor on 100% · 6.8 µH (2), 47 µH (1), 4.7 µH (1)
  • Series capacitor on 100% · 100 nF (5)
BST_6pin 6Connected to: Signal 100%
  • Series capacitor on 100% · 100 nF (5)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Gem solder by arlenko, Allfc by peregrine-developments, STM32F407VGTx-Connect by minhtenlado and Titan R3 by 1337bowen.

The AP63300WU-7 in open source designs

The gallery holds 5 open source boards using the AP63300WU-7 from 5 GitHub repositories; a typical one measures about 50.8 × 80 mm and carries around 96 components.

80% use four copper layers or more, and 80% carry an open source license.

The most starred is Allfc by peregrine-developments.

Parts used alongside the AP63300WU-7

Microcontrollers on boards using the AP63300WU-7

AP63300WU-7: common questions

Where can I find a AP63300WU-7 reference design?

Each of the 5 boards on this page is a real design using the AP63300WU-7. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the AP63300WU-7 VIN pin?

The VIN pin has a decoupling capacitor on 5 of 5 designs, most often 10 µF (then 100 nF). Counted from the KiCad layouts of 5 open source designs using the AP63300WU-7.

How is the AP63300WU-7 SW_5 pin connected?

The SW_5 pin has a inductor on 5 of 5 designs, most often 6.8 µH (then 47 µH). Counted from the KiCad layouts of 5 open source designs using the AP63300WU-7.

How is the AP63300WU-7 BST_6 pin connected?

The BST_6 pin has a series capacitor on 5 of 5 designs, most often 100 nF. Counted from the KiCad layouts of 5 open source designs using the AP63300WU-7.

Which microcontrollers do boards using the AP63300WU-7 use?

Most are built on Microchip SAM (2), STM32 (2) and ESP32 (1).

How big is a typical board using the AP63300WU-7?

The median is 50.8 × 80 mm, and 20% are two-layer designs.

What is the most popular open source board using the AP63300WU-7?

By GitHub stars, Allfc by peregrine-developments, with 6 stars.

Can I simulate one of these boards using the AP63300WU-7 before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part