12 open source boards using the APS6404L-3SQR
Real designs built with the APS6404L-3SQR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Picocart64 v2
khill25
105 × 60 mm152 parts4LCustom license26NXP
Mdt chipdown
andykarpov
94 × 79.6 mm61 parts2LMIT2RP2040/RP2350
Panel rp2350 20x20 rev2
iorodeo
45 × 45 mm556 parts6LCC-BY-4.01STM32
TSC board
bartkepl
100 × 100 mm408 parts4LMIT0FPGA
AL-MAWJA
m0-hassan
194 parts4LNo license0Tensorrail
skillsbuffcom
102 × 70 mm37 parts2LNo license0RP2040/RP2350
Panel rp2350 20x20 temp
iorodeo
45 × 45 mm556 parts6LCC-BY-4.01FPGA
Dspod up5k
emeb
26.4 × 41.7 mm63 parts4LMIT10RP2040/RP2350
Panel rp2350 20x20 tmp
iorodeo
45 × 45 mm556 parts6LCC-BY-4.01RP2040/RP2350
Panel rp2354 20x20
iorodeo
45 × 45 mm556 parts6LCC-BY-4.01RP2040/RP2350
Driver rp2350
iorodeo
45 × 45 mm462 parts6LCC-BY-4.01RP2040/RP2350
Panel rp2350 18x18
iorodeo
45 × 45 mm462 parts6LCC-BY-4.01
How designs wire the APS6404L-3SQR
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the APS6404L-3SQR connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a decoupling capacitor on 7 of 7 designs, most often 100 nF (then 1 µF).
- The CS pin has a pull-up to 3.3V on 4 of 7 designs, most often 10 kΩ (then 100 Ω).
- The WP/IO2_3 pin has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ.
- The CLK pin has a pull-up to 3.3V on 3 of 7 designs, most often 100 Ω (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CSpin 1 | Connected to: Signal 100% |
|
| WP/IO2_3pin 3 | Connected to: The microcontroller 29% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| CLKpin 6 | Connected to: The microcontroller 29%, a connector 29% |
|
| SIO3pin 7 | Connected to: The microcontroller 29% |
|
| VCCpin 8 | Connected to: 3.3V 86% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Picocart64 v2 by khill25, Dspod up5k by emeb, Mdt chipdown by andykarpov and Driver rp2350 by iorodeo.
The APS6404L-3SQR in open source designs
The gallery holds 12 open source boards using the APS6404L-3SQR from 7 GitHub repositories; a typical one measures about 45 × 45 mm and carries around 435 components.
83% use four copper layers or more, and 75% carry an open source license.
The most starred is Picocart64 v2 by khill25.
Microcontrollers on boards using the APS6404L-3SQR
What boards using the APS6404L-3SQR are built for
APS6404L-3SQR: common questions
Where can I find a APS6404L-3SQR reference design?
Each of the 12 boards on this page is a real design using the APS6404L-3SQR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the APS6404L-3SQR VCC pin?
The VCC pin has a decoupling capacitor on 7 of 7 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 7 open source designs using the APS6404L-3SQR.
What pull-up resistor is used on the APS6404L-3SQR CS pin?
The CS pin has a pull-up to 3.3V on 4 of 7 designs, most often 10 kΩ (then 100 Ω). Counted from the KiCad layouts of 7 open source designs using the APS6404L-3SQR.
What pull-up resistor is used on the APS6404L-3SQR WP/IO2_3 pin?
The WP/IO2_3 pin has a pull-up to 3.3V on 3 of 7 designs, most often 10 kΩ. Counted from the KiCad layouts of 7 open source designs using the APS6404L-3SQR.
Which microcontrollers do boards using the APS6404L-3SQR use?
Most are built on RP2040/RP2350 (7), FPGA (2), NXP (1) and STM32 (1).
How big is a typical board using the APS6404L-3SQR?
The median is 45 × 45 mm, and 17% are two-layer designs.
What is the most popular open source board using the APS6404L-3SQR?
By GitHub stars, Picocart64 v2 by khill25, with 26 stars.
Can I simulate one of these boards using the APS6404L-3SQR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.