6 open source boards using the ATTINY13A-SSU
Real designs built with the ATTINY13A-SSU, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Nescart
Keitark
99.7 × 63.9 mm84 parts6LMIT0AVR/Arduino
HallowBadges-Bat
makeristic
98.5 × 89.1 mm10 parts2LNo license0AVR/Arduino
HallowBadges-Ghost
makeristic
88.1 × 99.1 mm10 parts2LNo license0AVR/Arduino
HallowBadges-Pumpkin
makeristic
99.6 × 94.1 mm10 parts2LNo license0AVR/Arduino
DefcoNFC Hardware Badge
monero-project
70 × 100 mm31 parts2LCERN-OHL-1.2115AVR/Arduino
Attiny13a breakout board
amitesh-singh
28.3 × 22.4 mm8 parts2LGPL-3.01
How designs wire the ATTINY13A-SSU
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ATTINY13A-SSU connects to, and the resistors, capacitors and other passives placed on it.
- Pin 4 is tied to GND on 6 of 6 designs.
- Pin 8 is tied to VCC on 5 of 6 designs.
- Pin 5 has a series resistor on 4 of 6 designs, most often 220 Ω.
- Pin 3 is left unconnected on 4 of 6 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 3 | Connected to: Not connected 67% · a signal 33% | — |
| Pin 4 | Connected to: GND 100% | — |
| Pin 5 | Connected to: A connector 100% |
|
| Pin 8 | Connected to: VCC 83% · a signal 17% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include DefcoNFC Hardware Badge by monero-project, Attiny13a breakout board by amitesh-singh, Nescart by Keitark and HallowBadges-Bat by makeristic.
The ATTINY13A-SSU in open source designs
The gallery holds 6 open source boards using the ATTINY13A-SSU from 6 GitHub repositories; a typical one measures about 93.3 × 91.6 mm and carries around 10 components.
83% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is DefcoNFC Hardware Badge by monero-project.
Microcontrollers on boards using the ATTINY13A-SSU
What boards using the ATTINY13A-SSU are built for
ATTINY13A-SSU: common questions
Where can I find a ATTINY13A-SSU reference design?
Each of the 6 boards on this page is a real design using the ATTINY13A-SSU. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ATTINY13A-SSU pin 4 connected?
Pin 4 is tied to GND on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ATTINY13A-SSU.
How is the ATTINY13A-SSU pin 8 connected?
Pin 8 is tied to VCC on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ATTINY13A-SSU.
What resistor goes on the ATTINY13A-SSU pin 5?
Pin 5 has a series resistor on 4 of 6 designs, most often 220 Ω. Counted from the KiCad layouts of 6 open source designs using the ATTINY13A-SSU.
Which microcontrollers do boards using the ATTINY13A-SSU use?
Most are built on AVR/Arduino (5) and ESP32 (1).
How big is a typical board using the ATTINY13A-SSU?
The median is 93.3 × 91.6 mm, and 83% are two-layer designs.
What is the most popular open source board using the ATTINY13A-SSU?
By GitHub stars, DefcoNFC Hardware Badge by monero-project, with 115 stars.
Can I simulate one of these boards using the ATTINY13A-SSU before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.