13 open source boards using the BQ21040
Real designs built with the BQ21040, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
U blox gnss receiver
lpechacek
65.4 × 41.9 mm41 parts2LCC-BY-4.014AVR/Arduino
PiBook
Wren6991
85 × 85 mm83 parts2LBSD-3-Clause9Nordic nRF
Scale hx711
IoTReady
70 × 40 mm75 parts2LNo license7Cphp82001
calcpsu
56 × 44 mm26 parts2LCC-BY-NC-4.04TI MSP430/CC
Beagleconnect freedom
beagleboard
35.8 × 58 mm176 parts4LCC-BY-4.01STM32
Plant monitor
PimentoFr
50 × 74 mm168 parts4LNo license0AVR/Arduino
Laser rifle
Dade3e
56 × 15.6 mm27 parts2LNo license0Microchip SAM
Fpgaboy
Wren6991
50 × 50 mm89 parts4LNo license511ESP32
Paperd.ink final panel
paperdink
92.1 × 96.1 mm86 parts4LCC-BY-SA-4.09Nordic nRF
Scale ltc6915
IoTReady
70 × 40 mm71 parts2LNo license7AVR/Arduino
Lr 40
Dade3e
39 × 19 mm27 parts2LNo license0ESP32
Paperd.ink
paperdink
92.1 × 78.1 mm85 parts2LCC-BY-SA-4.09ESP32
Paperd.ink main
paperdink
92.1 × 78.1 mm82 parts4LCC-BY-SA-4.09
How designs wire the BQ21040
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the BQ21040 connects to, and the resistors, capacitors and other passives placed on it.
- The VIN pin has a decoupling capacitor on 9 of 9 designs, most often 1 µF (then 10 µF).
- The ISET pin has a resistor to GND on 8 of 9 designs, most often 1.2 kΩ (then 680 Ω).
- The CHG pin has a series resistor on 7 of 9 designs, most often 680 Ω (then 1.1 kΩ).
- The TS pin has a resistor to GND on 6 of 9 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| TSpin 1 | Connected to: Signal 100% |
|
| OUTpin 2 | Connected to: A connector 33% · BATT 44% |
|
| CHGpin 3 | Connected to: Signal 100% |
|
| ISETpin 4 | Connected to: Signal 100% |
|
| GNDpin 5 | Connected to: GND 100% | — |
| VINpin 6 | Connected to: 5V 56% · a signal 44% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Fpgaboy by Wren6991, U blox gnss receiver by lpechacek, Paperd.ink by paperdink and PiBook by Wren6991.
The BQ21040 in open source designs
The gallery holds 13 open source boards using the BQ21040 from 9 GitHub repositories; a typical one measures about 65.4 × 50 mm and carries around 82 components.
62% are two-layer designs, the rest use four layers or more, and 46% carry an open source license.
The most starred is Fpgaboy by Wren6991.
Parts used alongside the BQ21040
Microcontrollers on boards using the BQ21040
What boards using the BQ21040 are built for
BQ21040: common questions
Where can I find a BQ21040 reference design?
Each of the 13 boards on this page is a real design using the BQ21040. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the BQ21040 VIN pin?
The VIN pin has a decoupling capacitor on 9 of 9 designs, most often 1 µF (then 10 µF). Counted from the KiCad layouts of 9 open source designs using the BQ21040.
What resistor goes on the BQ21040 ISET pin?
The ISET pin has a resistor to GND on 8 of 9 designs, most often 1.2 kΩ (then 680 Ω). Counted from the KiCad layouts of 9 open source designs using the BQ21040.
What resistor goes on the BQ21040 CHG pin?
The CHG pin has a series resistor on 7 of 9 designs, most often 680 Ω (then 1.1 kΩ). Counted from the KiCad layouts of 9 open source designs using the BQ21040.
Which microcontrollers do boards using the BQ21040 use?
Most are built on AVR/Arduino (3), ESP32 (3), Nordic nRF (2) and Microchip SAM (1).
How big is a typical board using the BQ21040?
The median is 65.4 × 50 mm, and 62% are two-layer designs.
What is the most popular open source board using the BQ21040?
By GitHub stars, Fpgaboy by Wren6991, with 511 stars.
Can I simulate one of these boards using the BQ21040 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.