6 open source boards using the BQ25887RGER

Real designs built with the BQ25887RGER, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

6 boardsClear filters|Most starred

How designs wire the BQ25887RGER

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the BQ25887RGER connects to, and the resistors, capacitors and other passives placed on it.

  • The TS_7 pin has a series resistor on 5 of 5 designs, most often 5.23 kΩ (then 10 kΩ).
  • The ILIM_8 pin has a resistor to GND on 5 of 5 designs, most often 383 Ω (then 2.21 kΩ).
  • The MID_9 pin has a series resistor on 5 of 5 designs, most often 300 Ω (then 330 Ω).
  • The CBSET_10 pin has a series resistor on 5 of 5 designs, most often 82 Ω (then 10 Ω).
*PG_1pin 1Connected to: Signal 80% · not connected 20%
  • Pull-up to 3.3V on 60% · 10 kΩ (2), 100 kΩ (1)
CD_3pin 3Connected to: Signal 60% · not connected 20% · GND 20%
  • Pull-up to 3.3V on 40% · 10 kΩ (1), 100 kΩ (1)
SDA_4pin 4Connected to: The microcontroller 60%
  • Pull-up to 3.3V on 60% · 2.2 kΩ (3)
SCL_5pin 5Connected to: The microcontroller 60%
  • Pull-up to 3.3V on 60% · 2.2 kΩ (3)
*INT_6pin 6Connected to: The microcontroller 40%
  • Pull-up to 3.3V on 80% · 10 kΩ (3), 100 kΩ (1)
TS_7pin 7Connected to: Signal 100%
  • Series resistor on 100% · 5.23 kΩ (4), 10 kΩ (1)
  • Resistor to GND on 80% · 30.1 kΩ (3), 10 kΩ (1), 12.4 kΩ (1)
ILIM_8pin 8Connected to: Signal 100%
  • Resistor to GND on 100% · 383 Ω (2), 2.21 kΩ (1), 750 Ω (1)
MID_9pin 9Connected to: Signal 100%
  • Series resistor on 100% · 300 Ω (3), 330 Ω (1), 383 Ω (1)
CBSET_10pin 10Connected to: Signal 100%
  • Series resistor on 100% · 82 Ω (6), 10 Ω (1), 100 Ω (1)
REGN_11pin 11Connected to: Signal 100%
  • Series resistor on 80% · 5.23 kΩ (3), 10 kΩ (2), 100 kΩ (1)
  • Capacitor to GND on 80% · 4.7 µF (4)
BTST_12pin 12Connected to: Signal 100%
  • Series capacitor on 100% · 47 nF (5)
BAT_13pin 13Connected to: VBAT_CHG 60% · a signal 40%
  • Decoupling capacitor on 100% · 10 µF (8), 100 nF (2)
BAT_14pin 14Connected to: VBAT_CHG 60% · a signal 40%
  • Decoupling capacitor on 100% · 10 µF (8), 100 nF (2)
SNS_15pin 15Connected to: Signal 100%
  • Capacitor to GND on 100% · 22 µF (6), 47 µF (3)
SNS_16pin 16Connected to: Signal 100%
  • Capacitor to GND on 100% · 22 µF (6), 47 µF (3)
SW_17pin 17Connected to: Signal 100%
  • Series capacitor on 100% · 47 nF (5)
  • Inductor on 80% · 1 µH (4)
SW_18pin 18Connected to: Signal 100%
  • Series capacitor on 100% · 47 nF (5)
  • Inductor on 80% · 1 µH (4)
GND_19pin 19Connected to: GND 100%
GND_20pin 20Connected to: GND 100%
PMID_21pin 21Connected to: Signal 100%
  • Capacitor to GND on 100% · 10 µF (5), 22 µF (1)
  • Inductor on 80% · 1 µH (4)
PMID_22pin 22Connected to: Signal 100%
  • Capacitor to GND on 100% · 10 µF (5), 22 µF (1)
  • Inductor on 80% · 1 µH (4)
VBUS_23pin 23Connected to: VBUS_PROT 80% · a signal 20%
  • Decoupling capacitor on 80% · 1 µF (3), 4.7 µF (1), 47 µF (1)
GND_25pin 25Connected to: GND 100%

2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include PowerBox by Alvin-Alford, StratosCore by pantojinho, Quack core by HeyPCB and E0005-esp32-s3-5v controller by Karpuls.

The BQ25887RGER in open source designs

The gallery holds 6 open source boards using the BQ25887RGER from 6 GitHub repositories; a typical one measures about 101 × 73 mm and carries around 120 components.

80% use four copper layers or more, and 17% carry an open source license.

The most starred is StratosCore by pantojinho.

Parts used alongside the BQ25887RGER

Microcontrollers on boards using the BQ25887RGER

BQ25887RGER: common questions

Where can I find a BQ25887RGER reference design?

Each of the 6 boards on this page is a real design using the BQ25887RGER. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the BQ25887RGER TS_7 pin?

The TS_7 pin has a series resistor on 5 of 5 designs, most often 5.23 kΩ (then 10 kΩ). Counted from the KiCad layouts of 5 open source designs using the BQ25887RGER.

What resistor goes on the BQ25887RGER ILIM_8 pin?

The ILIM_8 pin has a resistor to GND on 5 of 5 designs, most often 383 Ω (then 2.21 kΩ). Counted from the KiCad layouts of 5 open source designs using the BQ25887RGER.

What resistor goes on the BQ25887RGER MID_9 pin?

The MID_9 pin has a series resistor on 5 of 5 designs, most often 300 Ω (then 330 Ω). Counted from the KiCad layouts of 5 open source designs using the BQ25887RGER.

Which microcontrollers do boards using the BQ25887RGER use?

Most are built on ESP32 (1), RP2040/RP2350 (1) and STM32 (1).

How big is a typical board using the BQ25887RGER?

The median is 101 × 73 mm, and 20% are two-layer designs.

What is the most popular open source board using the BQ25887RGER?

By GitHub stars, StratosCore by pantojinho, with 1 stars.

Can I simulate one of these boards using the BQ25887RGER before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part