8 open source boards using the C2913202
Real designs built with the C2913202, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Hex master motor control circuit
csiz
64 × 86 mm236 parts4LMIT9ESP32
Esp32-led controller
arkandas
93.4 × 42.6 mm61 parts2LMIT5ESP32
Ultisense
darshg321
44.7 × 93.6 mm83 parts2LNo license3ESP32
Nft hydroponic controller
hasan-abuzaid
135 × 101.3 mm97 parts4LCERN-OHL-S-2.00ESP32
Esp-Sumo
Dunbarin-O
175.2 × 64.7 mm84 parts4LNo license0ESP32
The card
clouds56-mcu
54 × 85.6 mm71 parts4LMIT0ESP32
Quadcopter
markusheimerl
75.1 × 75.1 mm60 parts2LUnlicense0- schematic only · 42 partsESP32
Watch
Resteral
42 partsNo license0
How designs wire the C2913202
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the C2913202 connects to, and the resistors, capacitors and other passives placed on it.
- The EN_3 pin has a capacitor to GND on 6 of 7 designs, most often 1 µF (then 100 nF).
- The EN_3 pin has a pull-up to 3.3V on 6 of 7 designs, most often 10 kΩ.
- The 3V3_2 pin is tied to 3.3V on 6 of 7 designs.
- The IO46_16 pin is left unconnected on 6 of 7 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GND_1pin 1 | Connected to: GND 100% | — |
| 3V3_2pin 2 | Connected to: 3.3V 86% | — |
| EN_3pin 3 | Connected to: Signal 100% |
|
| IO3_15pin 15 | Connected to: Not connected 71% · a signal 29% | — |
| IO46_16pin 16 | Connected to: Not connected 86% | — |
| IO10_18pin 18 | Connected to: A connector 57% |
|
| IO45_26pin 26 | Connected to: Not connected 86% | — |
| IO0_27pin 27 | Connected to: Signal 100% |
|
| IO35_28pin 28 | Connected to: Not connected 71% · a signal 29% | — |
| IO36_29pin 29 | Connected to: Not connected 71% · a signal 29% | — |
| IO37_30pin 30 | Connected to: Not connected 71% · a signal 29% | — |
| IO1_39pin 39 | Connected to: A connector 29% |
|
| GND_40pin 40 | Connected to: GND 100% | — |
| GND_41pin 41 | Connected to: GND 100% | — |
27 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Hex master motor control circuit by csiz, Esp32-led controller by arkandas, Ultisense by darshg321 and The card by clouds56-mcu.
The C2913202 in open source designs
The gallery holds 8 open source boards using the C2913202 from 8 GitHub repositories; a typical one measures about 75.1 × 85.6 mm and carries around 77 components.
57% use four copper layers or more, and 63% carry an open source license.
The most starred is Hex master motor control circuit by csiz.
Parts used alongside the C2913202
Microcontrollers on boards using the C2913202
What boards using the C2913202 are built for
C2913202: common questions
Where can I find a C2913202 reference design?
Each of the 8 boards on this page is a real design using the C2913202. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the C2913202 EN_3 pin connected?
The EN_3 pin has a capacitor to GND on 6 of 7 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 7 open source designs using the C2913202.
How is the C2913202 3V3_2 pin connected?
The 3V3_2 pin is tied to 3.3V on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the C2913202.
How is the C2913202 IO46_16 pin connected?
The IO46_16 pin is left unconnected on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the C2913202.
Which microcontrollers do boards using the C2913202 use?
Most are built on ESP32 (8).
How big is a typical board using the C2913202?
The median is 75.1 × 85.6 mm, and 43% are two-layer designs.
What is the most popular open source board using the C2913202?
By GitHub stars, Hex master motor control circuit by csiz, with 9 stars.
Can I simulate one of these boards using the C2913202 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.