9 open source boards using the CA56-12EWA

Real designs built with the CA56-12EWA, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

9 boardsClear filters|Most starred

How designs wire the CA56-12EWA

Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the CA56-12EWA connects to, and the resistors, capacitors and other passives placed on it.

  • The E_1 pin has a series resistor on 5 of 8 designs, most often 330 Ω (then 10 Ω).
  • The D_2 pin has a series resistor on 5 of 8 designs, most often 330 Ω (then 10 Ω).
  • The DPX_3 pin has a series resistor on 5 of 8 designs, most often 330 Ω (then 10 Ω).
  • The C_4 pin has a series resistor on 5 of 8 designs, most often 330 Ω (then 10 Ω).
E_1pin 1Connected to: Signal 100%
  • Series resistor on 63% · 330 Ω (3), 10 Ω (1), 100 Ω (1)
D_2pin 2Connected to: Signal 100%
  • Series resistor on 63% · 330 Ω (3), 10 Ω (1), 100 Ω (1)
DPX_3pin 3Connected to: Signal 100%
  • Series resistor on 63% · 330 Ω (3), 10 Ω (1), 100 Ω (1)
C_4pin 4Connected to: Signal 100%
  • Series resistor on 63% · 330 Ω (3), 10 Ω (1), 100 Ω (1)
G_5pin 5Connected to: Signal 100%
  • Series resistor on 63% · 330 Ω (3), 10 Ω (1), 100 Ω (1)
B_7pin 7Connected to: Signal 100%
  • Series resistor on 63% · 330 Ω (3), 10 Ω (1), 100 Ω (1)
F_10pin 10Connected to: Signal 100%
  • Series resistor on 63% · 330 Ω (3), 10 Ω (1), 100 Ω (1)
A_11pin 11Connected to: Signal 100%
  • Series resistor on 63% · 330 Ω (3), 10 Ω (1), 100 Ω (1)

4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ShieldArduino Displays7Segmentos by tidus747, Beat707 by FrankBuss, PCB-Temperature-Controller by MbFredys and Sentinel arduino firmware by YousefAliAicha.

The CA56-12EWA in open source designs

The gallery holds 9 open source boards using the CA56-12EWA from 8 GitHub repositories; a typical one measures about 100 × 114.3 mm and carries around 68 components.

89% are two-layer designs, the rest use four layers or more, and 56% carry an open source license.

The most starred is ShieldArduino Displays7Segmentos by tidus747.

Parts used alongside the CA56-12EWA

Microcontrollers on boards using the CA56-12EWA

What boards using the CA56-12EWA are built for

CA56-12EWA: common questions

Where can I find a CA56-12EWA reference design?

Each of the 9 boards on this page is a real design using the CA56-12EWA. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the CA56-12EWA E_1 pin?

The E_1 pin has a series resistor on 5 of 8 designs, most often 330 Ω (then 10 Ω). Counted from the KiCad layouts of 8 open source designs using the CA56-12EWA.

What resistor goes on the CA56-12EWA D_2 pin?

The D_2 pin has a series resistor on 5 of 8 designs, most often 330 Ω (then 10 Ω). Counted from the KiCad layouts of 8 open source designs using the CA56-12EWA.

What resistor goes on the CA56-12EWA DPX_3 pin?

The DPX_3 pin has a series resistor on 5 of 8 designs, most often 330 Ω (then 10 Ω). Counted from the KiCad layouts of 8 open source designs using the CA56-12EWA.

Which microcontrollers do boards using the CA56-12EWA use?

Most are built on AVR/Arduino (6).

How big is a typical board using the CA56-12EWA?

The median is 100 × 114.3 mm, and 89% are two-layer designs.

What is the most popular open source board using the CA56-12EWA?

By GitHub stars, ShieldArduino Displays7Segmentos by tidus747, with 12 stars.

Can I simulate one of these boards using the CA56-12EWA before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part