8 open source boards using the DRV8353SRTAT
Real designs built with the DRV8353SRTAT, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Open MOtor DRiver Initiative (OMODRI)
open-dynamic-robot-initiative
50 × 50 mm253 parts8LBSD-3-Clause122STM32
Bldc esc
EwoudVV
544 × 768 mm421 parts4LNo license1ESP32
Pace racer hardware
rammp-org
0 × 0 mm118 parts4LNo license0STM32
Controller
Choccy-vr
74.1 × 99.3 mm76 parts4LNo license0K-9R
HSabinoR
60 × 60 mm63 parts4LNo license0Omodri sa v2 laas
open-dynamic-robot-initiative
54.8 × 57.6 mm201 parts8LBSD-3-Clause122Omodri sa laas
open-dynamic-robot-initiative
54.8 × 57.6 mm194 parts8LBSD-3-Clause122Open MOtor DRiver Initiative (OMODRI) - Extension Board
open-dynamic-robot-initiative
50 × 50 mm167 parts6LBSD-3-Clause122
How designs wire the DRV8353SRTAT
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the DRV8353SRTAT connects to, and the resistors, capacitors and other passives placed on it.
- The CPL pin has a series capacitor on 4 of 5 designs, most often 47 nF.
- The CPH pin has a series capacitor on 4 of 5 designs, most often 47 nF.
- The SDO pin has a pull-up to 3.3V on 4 of 4 designs, most often 4.7 kΩ (then 73 kΩ).
- The VM pin has a series capacitor on 3 of 5 designs, most often 1 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| CPLpin 1 | Connected to: Signal 100% |
|
| CPHpin 2 | Connected to: Signal 80% · GND 20% |
|
| VMpin 3 | Connected to: Signal 60% · BATT 40% |
|
| VDRAINpin 4 | Connected to: BATT 60% · a signal 40% |
|
| VCPpin 5 | Connected to: Signal 80% · GND 20% |
|
| GHApin 6 | Connected to: Signal 100% |
|
| SHApin 7 | Connected to: A connector 100% |
|
| SPApin 9 | Connected to: Signal 80% · GND 20% |
|
| SNApin 10 | Connected to: Signal 75% · GND 25% |
|
| SNBpin 11 | Connected to: Signal 75% · GND 25% |
|
| SPBpin 12 | Connected to: Signal 100% |
|
| SHBpin 14 | Connected to: A connector 100% |
|
| SHCpin 17 | Connected to: A connector 100% |
|
| SPCpin 19 | Connected to: Signal 100% |
|
| SNCpin 20 | Connected to: Signal 75% · GND 25% |
|
| SOCpin 21 | Connected to: Signal 100% |
|
| SOBpin 22 | Connected to: Signal 100% |
|
| SOApin 23 | Connected to: Signal 100% |
|
| VREFpin 24 | Connected to: 3.3V 75% · a signal 25% |
|
| AGNDpin 25 | Connected to: GND 75% · a signal 25% | — |
| FAULT_Npin 26 | Connected to: The microcontroller 50% |
|
| SDOpin 27 | Connected to: The microcontroller 75% |
|
| ENABLEpin 31 | Connected to: The microcontroller 50% |
|
| INHApin 32 | Connected to: The microcontroller 50% |
|
| INLApin 33 | Connected to: The microcontroller 50% |
|
| INHBpin 34 | Connected to: The microcontroller 50% |
|
| INLBpin 35 | Connected to: The microcontroller 50% |
|
| INHCpin 36 | Connected to: The microcontroller 50% |
|
| INLCpin 37 | Connected to: The microcontroller 50% |
|
| DVDDpin 38 | Connected to: Signal 75% · DVDD 25% |
|
| PGNDpin 39 | Connected to: GND 75% · a signal 25% | — |
| VGLSpin 40 | Connected to: Signal 100% |
|
| PADpin 41 | Connected to: GND 75% · a signal 25% | — |
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Open MOtor DRiver Initiative (OMODRI) - Extension Board by open-dynamic-robot-initiative, Bldc esc by EwoudVV, Controller by Choccy-vr and K-9R by HSabinoR.
The DRV8353SRTAT in open source designs
The gallery holds 8 open source boards using the DRV8353SRTAT from 5 GitHub repositories; a typical one measures about 54.8 × 57.6 mm and carries around 181 components.
100% use four copper layers or more, and 50% carry an open source license.
The most starred is Open MOtor DRiver Initiative (OMODRI) by open-dynamic-robot-initiative.
Parts used alongside the DRV8353SRTAT
What boards using the DRV8353SRTAT are built for
DRV8353SRTAT: common questions
Where can I find a DRV8353SRTAT reference design?
Each of the 8 boards on this page is a real design using the DRV8353SRTAT. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the DRV8353SRTAT CPL pin connected?
The CPL pin has a series capacitor on 4 of 5 designs, most often 47 nF. Counted from the KiCad layouts of 5 open source designs using the DRV8353SRTAT.
How is the DRV8353SRTAT CPH pin connected?
The CPH pin has a series capacitor on 4 of 5 designs, most often 47 nF. Counted from the KiCad layouts of 5 open source designs using the DRV8353SRTAT.
What pull-up resistor is used on the DRV8353SRTAT SDO pin?
The SDO pin has a pull-up to 3.3V on 4 of 4 designs, most often 4.7 kΩ (then 73 kΩ). Counted from the KiCad layouts of 5 open source designs using the DRV8353SRTAT.
Which microcontrollers do boards using the DRV8353SRTAT use?
Most are built on STM32 (2) and ESP32 (1).
How big is a typical board using the DRV8353SRTAT?
The median is 54.8 × 57.6 mm, and 0% are two-layer designs.
What is the most popular open source board using the DRV8353SRTAT?
By GitHub stars, Open MOtor DRiver Initiative (OMODRI) by open-dynamic-robot-initiative, with 122 stars.
Can I simulate one of these boards using the DRV8353SRTAT before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.