15 open source boards using the DS3231SN
Real designs built with the DS3231SN, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Gpstracker
blemasle
79.3 × 59.2 mm65 parts2LMIT33FPGA
ZYNQ Ruler
Stanlazy
88 × 23.4 mm217 parts4LLGPL-2.117- schematic only · 10 partsSTM32
Hip
8adam95
10 partsNo license2 - schematic only · 67 partsAVR/Arduino
Tiny alarm
mufeedcm
67 partsGPL-3.01 ESP32
Esp32 s3 dwm3000 uwb anchor with relay outputs
Takingo
160 × 100 mm322 parts4LNo license0ESP32
Exhaust mic
HasiKe
72 × 55 mm133 parts4LNo license0RP2040/RP2350
Led processor board
eelstretching
100 × 89.5 mm123 parts2LNo license0Microchip SAM
SapphineMinimalR6
ChrisHayward-dev
55.9 × 61 mm121 parts4LNo license0ESP32
Secure edge logger
landjas09
87.5 × 54.7 mm92 parts4LNo license0SmartFarm
AntonSangho
80 × 79.1 mm36 parts2LNo license0ESP32
Medivault
chislonljoseph
98.5 × 47 mm32 parts2LNo license0Quantum mind uwb rtls anchor v3 0
Takingo
220 × 140 mm193 parts4LNo license0AVR/Arduino
SuperClockController
silicagel777
139.7 × 48.3 mm77 parts2LMIT0Quantum mind uwb rtls anchor v3 0 fr224 java25 test
Takingo
220 × 140 mm193 parts4LNo license0Quantum mind uwb rtls anchor v3 0 fr224 test
Takingo
220 × 140 mm193 parts4LNo license0
How designs wire the DS3231SN
Read from the KiCad layouts of 10 open source designs, one per repository: what each pin of the DS3231SN connects to, and the resistors, capacitors and other passives placed on it.
- The SDA pin has a pull-up to 3.3V on 7 of 9 designs, most often 4.7 kΩ (then 1 kΩ).
- The SCL pin has a pull-up to 3.3V on 7 of 9 designs, most often 4.7 kΩ (then 1 kΩ).
- The 32KHZ pin is left unconnected on 8 of 10 designs (a signal on 2).
- The RST pin is left unconnected on 8 of 10 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| 32KHZpin 1 | Connected to: Not connected 80% · a signal 20% | — |
| VCCpin 2 | Connected to: 3.3V 90% |
|
| INT/SQWpin 3 | Connected to: The microcontroller 50% · not connected 40% |
|
| RSTpin 4 | Connected to: Not connected 80% · a signal 20% | — |
| SDApin 15 | Connected to: The microcontroller 78%, a connector 56% |
|
| SCLpin 16 | Connected to: The microcontroller 78%, a connector 56% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Gpstracker by blemasle, ZYNQ Ruler by Stanlazy, SmartFarm PCB by AntonSangho and Medivault by chislonljoseph.
The DS3231SN in open source designs
The gallery holds 15 open source boards using the DS3231SN from 12 GitHub repositories; a typical one measures about 98.5 × 61 mm and carries around 121 components.
62% use four copper layers or more, and 27% carry an open source license.
The most starred is Gpstracker by blemasle.
Parts used alongside the DS3231SN
Microcontrollers on boards using the DS3231SN
What boards using the DS3231SN are built for
DS3231SN: common questions
Where can I find a DS3231SN reference design?
Each of the 15 boards on this page is a real design using the DS3231SN. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the DS3231SN SDA pin?
The SDA pin has a pull-up to 3.3V on 7 of 9 designs, most often 4.7 kΩ (then 1 kΩ). Counted from the KiCad layouts of 10 open source designs using the DS3231SN.
What pull-up resistor is used on the DS3231SN SCL pin?
The SCL pin has a pull-up to 3.3V on 7 of 9 designs, most often 4.7 kΩ (then 1 kΩ). Counted from the KiCad layouts of 10 open source designs using the DS3231SN.
How is the DS3231SN 32KHZ pin connected?
The 32KHZ pin is left unconnected on 8 of 10 designs (a signal on 2). Counted from the KiCad layouts of 10 open source designs using the DS3231SN.
Which microcontrollers do boards using the DS3231SN use?
Most are built on ESP32 (4), AVR/Arduino (3), FPGA (1) and RP2040/RP2350 (1).
How big is a typical board using the DS3231SN?
The median is 98.5 × 61 mm, and 38% are two-layer designs.
What is the most popular open source board using the DS3231SN?
By GitHub stars, Gpstracker by blemasle, with 33 stars.
Can I simulate one of these boards using the DS3231SN before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.