10 open source boards using the ESP-07v2
Real designs built with the ESP-07v2, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Opensolar
junglejim8
60.5 × 100 mm147 parts2LNo license23STM32
Wifi iot core hw
genuine-engineering
31.8 × 58.4 mm45 parts2LNo license12Espled
Yottabits
100 × 50 mm41 parts2LNo license6BenTo-Legacy
benkuper
142 × 23 mm76 parts2LGPL-3.01Esp8266 test board (Copie en conflit de Steven 2015-08-28)
sifourquier
64 × 80 mm120 parts2LNo license0ESP8266
PowMetV2.2
aleksejm
95.2 × 67.5 mm155 parts2LNo license7.kicad
sifourquier
52.2 × 52.9 mm51 parts2LNo license0Button
sifourquier
53.5 × 108.5 mm49 parts2LNo license0Esp8266 test board (Copie en conflit de Simon Fourquier 2015-08-26)
sifourquier
64 × 21.5 mm32 parts2LNo license0Esp8266 test board
sifourquier
64 × 21.5 mm31 parts2LNo license0
How designs wire the ESP-07v2
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ESP-07v2 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 8 is tied to 3.3V on 6 of 6 designs.
- Pin 9 is tied to GND on 5 of 6 designs.
- Pin 3 has a pull-up to 3.3V on 4 of 6 designs, most often 10 kΩ.
- Pin 8 has a decoupling capacitor on 4 of 6 designs, most often 100 nF (then 100 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| Pin 2 | Connected to: Not connected 50% · a signal 50% |
|
| Pin 3 | Connected to: Signal 67% · 3.3V 33% |
|
| Pin 4 | Connected to: Signal 83% · not connected 17% |
|
| Pin 8 | Connected to: 3.3V 100% |
|
| Pin 9 | Connected to: GND 83% · not connected 17% | — |
| Pin 10 | Connected to: Signal 83% · not connected 17% |
|
| Pin 11 | Connected to: Signal 83% · not connected 17% |
|
| Pin 12 | Connected to: A connector 50% · not connected 17% |
|
| Pin 13 | Connected to: Signal 67% · not connected 33% |
|
6 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Opensolar by junglejim8, Wifi iot core hw by genuine-engineering, PowMetV2.2 by aleksejm and Espled by Yottabits.
The ESP-07v2 in open source designs
The gallery holds 10 open source boards using the ESP-07v2 from 6 GitHub repositories; a typical one measures about 64 × 55.7 mm and carries around 50 components.
100% are two-layer designs, the rest use four layers or more, and 10% carry an open source license.
The most starred is Opensolar by junglejim8.
What boards using the ESP-07v2 are built for
ESP-07v2: common questions
Where can I find a ESP-07v2 reference design?
Each of the 10 boards on this page is a real design using the ESP-07v2. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ESP-07v2 pin 8 connected?
Pin 8 is tied to 3.3V on 6 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ESP-07v2.
How is the ESP-07v2 pin 9 connected?
Pin 9 is tied to GND on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ESP-07v2.
What pull-up resistor is used on the ESP-07v2 pin 3?
Pin 3 has a pull-up to 3.3V on 4 of 6 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the ESP-07v2.
Which microcontrollers do boards using the ESP-07v2 use?
Most are built on ESP8266 (1) and STM32 (1).
How big is a typical board using the ESP-07v2?
The median is 64 × 55.7 mm, and 100% are two-layer designs.
What is the most popular open source board using the ESP-07v2?
By GitHub stars, Opensolar by junglejim8, with 23 stars.
Can I simulate one of these boards using the ESP-07v2 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.