7 open source boards using the ESP-32S
Real designs built with the ESP-32S, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Smartdisplay hardware
BearLaboratory
83.2 × 40 mm46 parts2LGPL-3.0175ESP32
Wifiaudio tx hardware
BearLaboratory
35.4 × 27 mm29 parts2LGPL-3.0110ESP32
Wifiaudio rx hardware
BearLaboratory
42 × 30.8 mm52 parts2LGPL-3.020ESP32
A3 8p redFIS
tothpetiszilard
124 × 40 mm77 parts2LAGPL-3.015ESP32
BREAN
uawortu
82 × 35 mm85 parts4LNo license2ESP32
Esp32wroomOled V01
erkanCil
47.5 × 56.8 mm60 parts2LNo license2Thermometer
LudovicLemarinel
36.9 × 36.9 mm12 parts2LNo license3
How designs wire the ESP-32S
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the ESP-32S connects to, and the resistors, capacitors and other passives placed on it.
- The EN pin has a pull-up to 3.3V on 7 of 7 designs, most often 10 kΩ (then 1 kΩ).
- The 3V3 pin is tied to 3.3V on 7 of 7 designs.
- The EN pin has a capacitor to GND on 5 of 7 designs, most often 1 µF (then 100 nF).
- The CMD pin is left unconnected on 6 of 7 designs.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 15, 38 | Connected to: GND 95% | — |
| 3V3pin 2 | Connected to: 3.3V 100% | — |
| ENpin 3 | Connected to: A connector 43% |
|
| IO34pin 6 | Connected to: A connector 29% · not connected 29% |
|
| IO35pin 7 | Connected to: Not connected 71% · a signal 29% | — |
| IO14pin 13 | Connected to: A connector 29% · not connected 43% |
|
| SD2pin 17 | Connected to: Not connected 71% · a signal 29% | — |
| SD3pin 18 | Connected to: Not connected 71% · a signal 29% | — |
| CMDpin 19 | Connected to: Not connected 86% | — |
| CLKpin 20 | Connected to: Not connected 86% | — |
| SDOpin 21 | Connected to: Not connected 71% · a signal 29% | — |
| SD1pin 22 | Connected to: Not connected 71% · a signal 29% | — |
| IO15pin 23 | Connected to: Not connected 71% · a signal 29% | — |
| IO0pin 25 | Connected to: A connector 71% |
|
| NCpin 32 | Connected to: Not connected 100% | — |
| GND-PADpin 39 | Connected to: GND 100% | — |
21 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Smartdisplay hardware by BearLaboratory, Wifiaudio tx hardware by BearLaboratory, Wifiaudio rx hardware by BearLaboratory and A3 8p redFIS by tothpetiszilard.
The ESP-32S in open source designs
The gallery holds 7 open source boards using the ESP-32S from 7 GitHub repositories; a typical one measures about 47.5 × 36.9 mm and carries around 52 components.
86% are two-layer designs, the rest use four layers or more, and 57% carry an open source license.
The most starred is Smartdisplay hardware by BearLaboratory.
Parts used alongside the ESP-32S
Microcontrollers on boards using the ESP-32S
What boards using the ESP-32S are built for
ESP-32S: common questions
Where can I find a ESP-32S reference design?
Each of the 7 boards on this page is a real design using the ESP-32S. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ESP-32S EN pin?
The EN pin has a pull-up to 3.3V on 7 of 7 designs, most often 10 kΩ (then 1 kΩ). Counted from the KiCad layouts of 7 open source designs using the ESP-32S.
How is the ESP-32S 3V3 pin connected?
The 3V3 pin is tied to 3.3V on 7 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the ESP-32S.
How is the ESP-32S CMD pin connected?
The CMD pin is left unconnected on 6 of 7 designs. Counted from the KiCad layouts of 7 open source designs using the ESP-32S.
What parts are used alongside the ESP-32S?
The AMS1117-3.3, ME6211C33M5G-N, PCM5102A and TP4056 appear in the most repositories here.
Which microcontrollers do boards using the ESP-32S use?
Most are built on ESP32 (6).
How big is a typical board using the ESP-32S?
The median is 47.5 × 36.9 mm, and 86% are two-layer designs.
What is the most popular open source board using the ESP-32S?
By GitHub stars, Smartdisplay hardware by BearLaboratory, with 175 stars.
Can I simulate one of these boards using the ESP-32S before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.