6 open source boards using the ESP32-S3-MINI-1U-N8
Real designs built with the ESP32-S3-MINI-1U-N8, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Controller
sudo-junkie
127.9 × 33.6 mm101 parts4LNo license1ESP32
MR1
EpicQuestBio
80 × 60 mm101 parts4LAGPL-3.00ESP32
MR1
LokiMetaSmith
80 × 60 mm101 parts4LAGPL-3.00ESP32
ESP BMCU
mengxyz
31.2 × 99.6 mm74 parts2LGPL-3.00ESP32
Pixel snap voice
zeeman-effect
64 × 86 mm55 parts4LNo license0ESP32
ESP32-S3-Mini-1U
uutzinger
20.3 × 38.1 mm38 parts2LNo license0
How designs wire the ESP32-S3-MINI-1U-N8
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the ESP32-S3-MINI-1U-N8 connects to, and the resistors, capacitors and other passives placed on it.
- The EN_45 pin has a pull-up to 3.3V on 5 of 5 designs, most often 10 kΩ.
- The EN_45 pin has a capacitor to GND on 5 of 5 designs, most often 4.7 µF (then 100 nF).
- The 3V3_3 pin is tied to 3.3V on 5 of 6 designs.
- The IO15_19 pin has a series resistor on 3 of 6 designs, most often 0 Ω.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GND_1pin 1 | Connected to: GND 100% | — |
| GND_2pin 2 | Connected to: GND 83% · 3.3V 17% | — |
| 3V3_3pin 3 | Connected to: 3.3V 83% · a signal 17% | — |
| IO0_4pin 4 | Connected to: Signal 67% · not connected 33% |
|
| IO5_9pin 9 | Connected to: A connector 33% |
|
| IO6_10pin 10 | Connected to: A connector 50% |
|
| IO7_11pin 11 | Connected to: A connector 50% |
|
| IO8_12pin 12 | Connected to: A connector 33% |
|
| IO9_13pin 13 | Connected to: A connector 33% |
|
| IO10_14pin 14 | Connected to: Signal 100% |
|
| IO11_15pin 15 | Connected to: Signal 100% |
|
| IO12_16pin 16 | Connected to: Signal 100% |
|
| IO15_19pin 19 | Connected to: A connector 33% |
|
| IO16_20pin 20 | Connected to: A connector 33% |
|
| USB_D-_23pin 23 | Connected to: A connector 50% |
|
| USB_D+_24pin 24 | Connected to: A connector 50% |
|
| IO21_25pin 25 | Connected to: A connector 33% · not connected 17% |
|
| IO26_26pin 26 | Connected to: Signal 83% · not connected 17% |
|
| IO40_36pin 36 | Connected to: A connector 67% · not connected 17% |
|
| IO41_37pin 37 | Connected to: A connector 67% · not connected 17% |
|
| TXD0_39pin 39 | Connected to: A connector 67% |
|
| RXD0_40pin 40 | Connected to: A connector 50% · GND 17% |
|
| GND_42pin 42 | Connected to: GND 100% | — |
| GND_43pin 43 | Connected to: GND 100% | — |
| IO46_44pin 44 | Connected to: A connector 60% · not connected 20% |
|
| EN_45pin 45 | Connected to: A connector 40% |
|
| GND_46pin 46 | Connected to: GND 100% | — |
| GND_47pin 47 | Connected to: GND 100% | — |
| GND_48pin 48 | Connected to: GND 100% | — |
| GND_49pin 49 | Connected to: GND 100% | — |
| GND_50pin 50 | Connected to: GND 100% | — |
| GND_51pin 51 | Connected to: GND 100% | — |
| GND_52pin 52 | Connected to: GND 100% | — |
| GND_53pin 53 | Connected to: GND 100% | — |
| GND_54pin 54 | Connected to: GND 100% | — |
| GND_55pin 55 | Connected to: GND 100% | — |
| GND_56pin 56 | Connected to: GND 100% | — |
| GND_57pin 57 | Connected to: GND 100% | — |
| GND_58pin 58 | Connected to: GND 100% | — |
| GND_59pin 59 | Connected to: GND 100% | — |
25 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Controller by sudo-junkie, MR1 by EpicQuestBio, MR1 by LokiMetaSmith and ESP BMCU by mengxyz.
The ESP32-S3-MINI-1U-N8 in open source designs
The gallery holds 6 open source boards using the ESP32-S3-MINI-1U-N8 from 6 GitHub repositories; a typical one measures about 72 × 60 mm and carries around 88 components.
67% use four copper layers or more, and 50% carry an open source license.
The most starred is Controller by sudo-junkie.
Parts used alongside the ESP32-S3-MINI-1U-N8
Microcontrollers on boards using the ESP32-S3-MINI-1U-N8
What boards using the ESP32-S3-MINI-1U-N8 are built for
ESP32-S3-MINI-1U-N8: common questions
Where can I find a ESP32-S3-MINI-1U-N8 reference design?
Each of the 6 boards on this page is a real design using the ESP32-S3-MINI-1U-N8. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What pull-up resistor is used on the ESP32-S3-MINI-1U-N8 EN_45 pin?
The EN_45 pin has a pull-up to 3.3V on 5 of 5 designs, most often 10 kΩ. Counted from the KiCad layouts of 6 open source designs using the ESP32-S3-MINI-1U-N8.
How is the ESP32-S3-MINI-1U-N8 3V3_3 pin connected?
The 3V3_3 pin is tied to 3.3V on 5 of 6 designs. Counted from the KiCad layouts of 6 open source designs using the ESP32-S3-MINI-1U-N8.
What resistor goes on the ESP32-S3-MINI-1U-N8 IO15_19 pin?
The IO15_19 pin has a series resistor on 3 of 6 designs, most often 0 Ω. Counted from the KiCad layouts of 6 open source designs using the ESP32-S3-MINI-1U-N8.
What parts are used alongside the ESP32-S3-MINI-1U-N8?
The ADR4520ARZ-R7, LM27762DSSR, LT3045EDD-1#TRPBF, LT3094EDD#TRPBF and MCP4822T-E/SN appear in the most repositories here.
Which microcontrollers do boards using the ESP32-S3-MINI-1U-N8 use?
Most are built on ESP32 (6).
How big is a typical board using the ESP32-S3-MINI-1U-N8?
The median is 72 × 60 mm, and 33% are two-layer designs.
What is the most popular open source board using the ESP32-S3-MINI-1U-N8?
By GitHub stars, Controller by sudo-junkie, with 1 stars.
Can I simulate one of these boards using the ESP32-S3-MINI-1U-N8 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.