10 open source boards using the ESP8266-1
Real designs built with the ESP8266-1, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP8266
POV-Globe
Mikail-Sadic-UT
83.6 × 86.6 mm95 parts2LNo license40ESP8266
ECE445L Final Project
DylanMeeks
152.4 × 127 mm241 parts2LNo license0ESP8266
ECE 445L Baseline Project
mjetpurwala
194.9 × 93 mm61 parts2LNo license0ESP8266
ECE 319K Baseline Project
mjetpurwala
114.3 × 88.9 mm40 parts2LNo license0ESP8266
ECE 445L Baseline Project
Joshua-Koshy
115 × 94 mm16 parts2LNo license0ESP8266
ECE 445L Baseline Project
tanai-prathapam
115 × 94 mm16 parts2LNo license0ESP8266
ECE 445L Baseline Project
tanai-prathapam
115 × 94 mm16 parts2LNo license0ESP8266
ECE 445L Baseline Project
tanai-prathapam
115 × 94 mm16 parts2LNo license0ESP8266
ECE 445L Baseline Project
DylanMeeks
115 × 94 mm16 parts2LNo license0ESP8266
ECE 445L Baseline Project
tanai-prathapam
115 × 94 mm16 parts2LNo license0
How designs wire the ESP8266-1
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the ESP8266-1 connects to, and the resistors, capacitors and other passives placed on it.
- The VCC pin has a capacitor to GND on 7 of 8 designs, most often 100 nF (then 4.7 µF).
- The GPIO0 pin has a series resistor on 6 of 8 designs, most often 10 kΩ.
- The GPIO0 pin has a capacitor to GND on 6 of 8 designs, most often 100 nF (then 4.7 µF).
- The CH_PD pin has a series resistor on 6 of 8 designs, most often 10 kΩ.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GPIO0pin 2 | Connected to: A connector 63% |
|
| GNDpin 4 | Connected to: GND 100% | — |
| CH_PDpin 6 | Connected to: Signal 88% |
|
| VCCpin 8 | Connected to: A connector 63% · 3.3V 25% |
|
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include POV-Globe by Mikail-Sadic-UT, ECE445L Final Project by DylanMeeks, ECE 445L Baseline Project by Joshua-Koshy and ECE 445L Baseline Project by mjetpurwala.
The ESP8266-1 in open source designs
The gallery holds 10 open source boards using the ESP8266-1 from 8 GitHub repositories; a typical one measures about 115 × 94 mm and carries around 16 components.
100% are two-layer designs, the rest use four layers or more, and 0% carry an open source license.
The most starred is POV-Globe by Mikail-Sadic-UT.
Parts used alongside the ESP8266-1
Microcontrollers on boards using the ESP8266-1
What boards using the ESP8266-1 are built for
ESP8266-1: common questions
Where can I find a ESP8266-1 reference design?
Each of the 10 boards on this page is a real design using the ESP8266-1. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ESP8266-1 VCC pin connected?
The VCC pin has a capacitor to GND on 7 of 8 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 8 open source designs using the ESP8266-1.
What resistor goes on the ESP8266-1 GPIO0 pin?
The GPIO0 pin has a series resistor on 6 of 8 designs, most often 10 kΩ. Counted from the KiCad layouts of 8 open source designs using the ESP8266-1.
What resistor goes on the ESP8266-1 CH_PD pin?
The CH_PD pin has a series resistor on 6 of 8 designs, most often 10 kΩ. Counted from the KiCad layouts of 8 open source designs using the ESP8266-1.
What parts are used alongside the ESP8266-1?
The Adafruit ST7735R, EK-TM4C123GXL, LM4041CILPR, TLV5616 and LM2937ET-3.3/NOPB appear in the most repositories here.
Which microcontrollers do boards using the ESP8266-1 use?
Most are built on ESP8266 (10).
How big is a typical board using the ESP8266-1?
The median is 115 × 94 mm, and 100% are two-layer designs.
What is the most popular open source board using the ESP8266-1?
By GitHub stars, POV-Globe by Mikail-Sadic-UT, with 40 stars.
Can I simulate one of these boards using the ESP8266-1 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.