5 open source boards using the MCP6486UT-E/LT

Real designs built with the MCP6486UT-E/LT, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

5 boardsClear filters|Most starred

How designs wire the MCP6486UT-E/LT

Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the MCP6486UT-E/LT connects to, and the resistors, capacitors and other passives placed on it.

  • The - pin has a series capacitor on 5 of 5 designs, most often 20 pF (then 470 pF).
  • The - pin has a series resistor on 5 of 5 designs, most often 27 kΩ (then 12 kΩ).
  • Pin 4 has a series capacitor on 5 of 5 designs, most often 20 pF (then 470 pF).
  • Pin 4 has a series resistor on 5 of 5 designs, most often 12 kΩ (then 12.1 kΩ).
+pin 1Connected to: Signal 100%
  • Series resistor on 80% · 27 kΩ (3), 10 kΩ (1)
  • Pull-up to VREF_DGND on 60% · 12 kΩ (2), 12.1 kΩ (1)
V-pin 2Connected to: GND 100%
-pin 3Connected to: Signal 100%
  • Series capacitor on 100% · 20 pF (3), 470 pF (1), 22 pF (1)
  • Series resistor on 100% · 27 kΩ (4), 12 kΩ (2), 10 kΩ (1)
Pin 4Connected to: OwnTech_SPIN 60%
  • Series capacitor on 100% · 20 pF (3), 470 pF (1), 22 pF (1)
  • Series resistor on 100% · 12 kΩ (2), 12.1 kΩ (1), 560 Ω (1)
V+pin 5Connected to: 5V 80% · a signal 20%
  • Decoupling capacitor on 100% · 100 nF (4), 4.7 µF (2), 22 µF (2)

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include UVerter by owntech-foundation, TWIST V1.4 by owntech-foundation, OWNVERTER by owntech-foundation and TWIST-board by RenewableEnergyNexus.

The MCP6486UT-E/LT in open source designs

The gallery holds 5 open source boards using the MCP6486UT-E/LT from 5 GitHub repositories; a typical one measures about 100 × 160 mm and carries around 325 components.

100% use four copper layers or more, and 40% carry an open source license.

The most starred is UVerter by owntech-foundation.

Microcontrollers on boards using the MCP6486UT-E/LT

What boards using the MCP6486UT-E/LT are built for

MCP6486UT-E/LT: common questions

Where can I find a MCP6486UT-E/LT reference design?

Each of the 5 boards on this page is a real design using the MCP6486UT-E/LT. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the MCP6486UT-E/LT - pin connected?

The - pin has a series capacitor on 5 of 5 designs, most often 20 pF (then 470 pF). Counted from the KiCad layouts of 5 open source designs using the MCP6486UT-E/LT.

How is the MCP6486UT-E/LT pin 4 connected?

Pin 4 has a series capacitor on 5 of 5 designs, most often 20 pF (then 470 pF). Counted from the KiCad layouts of 5 open source designs using the MCP6486UT-E/LT.

What decoupling capacitors do designs use on the MCP6486UT-E/LT V+ pin?

The V+ pin has a decoupling capacitor on 5 of 5 designs, most often 100 nF (then 4.7 µF). Counted from the KiCad layouts of 5 open source designs using the MCP6486UT-E/LT.

What parts are used alongside the MCP6486UT-E/LT?

The OwnTech_SPIN, AMC1100DUB, AMC1311BDWVR, AZ1117CH-5.0TRG1 and FODM217A appear in the most repositories here.

Which microcontrollers do boards using the MCP6486UT-E/LT use?

Most are built on PIC (1).

How big is a typical board using the MCP6486UT-E/LT?

The median is 100 × 160 mm, and 0% are two-layer designs.

What is the most popular open source board using the MCP6486UT-E/LT?

By GitHub stars, UVerter by owntech-foundation, with 112 stars.

Can I simulate one of these boards using the MCP6486UT-E/LT before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part