10 open source boards using the FT232RL-REEL

Real designs built with the FT232RL-REEL, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

10 boardsClear filters|Most starred

How designs wire the FT232RL-REEL

Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the FT232RL-REEL connects to, and the resistors, capacitors and other passives placed on it.

  • The RI pin is left unconnected on 9 of 9 designs.
  • The DSR# pin is left unconnected on 9 of 9 designs.
  • The DCD pin is left unconnected on 9 of 9 designs.
  • The OSCI pin is left unconnected on 9 of 9 designs.
DTRpin 2Connected to: A connector 22% · not connected 33%
  • Series capacitor on 33% · 100 nF (3)
RTSpin 3Connected to: Not connected 67% · a signal 33%
VCCIOpin 4Connected to: 3.3V 67% · a signal 33%
  • Decoupling capacitor on 33% · 100 nF (5), 10 µF (2), 4.7 µF (1)
RIpin 6Connected to: Not connected 100%
GNDpin 7, 18, 21Connected to: GND 100%
NCpin 8, 24Connected to: Not connected 100%
DSR#pin 9Connected to: Not connected 100%
DCDpin 10Connected to: Not connected 100%
CTSpin 11Connected to: Not connected 67% · a signal 33%
CBUS4pin 12Connected to: Not connected 89%
CBUS2pin 13Connected to: Not connected 89%
CBUS3pin 14Connected to: Not connected 78% · a signal 22%
3V3OUTpin 17Connected to: Signal 56% · not connected 22% · 3.3V 22%
  • Capacitor to GND on 67% · 100 nF (6)
RESETpin 19Connected to: Signal 56% · not connected 33%
  • Pull-up to 5V on 33% · 10 kΩ (3)
VCCpin 20Connected to: 5V 89%
  • Decoupling capacitor on 78% · 100 nF (8), 4.7 µF (3), 10 µF (2)
CBUS1pin 22Connected to: Signal 89%
  • Series resistor on 33% · 1 kΩ (3)
CBUS0pin 23Connected to: Signal 89%
  • Series resistor on 33% · 1 kΩ (3)
AGNDpin 25Connected to: GND 100%
TESTpin 26Connected to: GND 89%
OSCIpin 27Connected to: Not connected 100%
OSCOpin 28Connected to: Not connected 100%

4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Motherboard by ParadigmHyperloop, Alcantara by zenitheesc, Stepper driver by harp-tech and Main by chiplet.

The FT232RL-REEL in open source designs

The gallery holds 10 open source boards using the FT232RL-REEL from 9 GitHub repositories; a typical one measures about 100.8 × 76.2 mm and carries around 95 components.

60% use four copper layers or more, and 10% carry an open source license.

The most starred is Motherboard by ParadigmHyperloop.

Microcontrollers on boards using the FT232RL-REEL

FT232RL-REEL: common questions

Where can I find a FT232RL-REEL reference design?

Each of the 10 boards on this page is a real design using the FT232RL-REEL. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

How is the FT232RL-REEL RI pin connected?

The RI pin is left unconnected on 9 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the FT232RL-REEL.

How is the FT232RL-REEL DSR# pin connected?

The DSR# pin is left unconnected on 9 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the FT232RL-REEL.

How is the FT232RL-REEL DCD pin connected?

The DCD pin is left unconnected on 9 of 9 designs. Counted from the KiCad layouts of 9 open source designs using the FT232RL-REEL.

What parts are used alongside the FT232RL-REEL?

The ATMEGA328PB-ANR, AZ1117CH-3.3TRG1, LM2576HVS-5.0_NOPB, Pololu_DRV8711_Motor_Driver and TXB0108PWR appear in the most repositories here.

Which microcontrollers do boards using the FT232RL-REEL use?

Most are built on AVR/Arduino (5), ESP32 (2) and STM32 (2).

How big is a typical board using the FT232RL-REEL?

The median is 100.8 × 76.2 mm, and 40% are two-layer designs.

What is the most popular open source board using the FT232RL-REEL?

By GitHub stars, Motherboard by ParadigmHyperloop, with 11 stars.

Can I simulate one of these boards using the FT232RL-REEL before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part