6 open source boards using the FT234XD-R
Real designs built with the FT234XD-R, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Raspberry Pi
Scalenode cm4-baseboard
antmicro
128.5 × 40 mm125 parts4LApache-2.0151Evalboard1
mschuldt
67.6 × 45.3 mm37 parts2LNo license6STM32
STM32SESNSEHAT
Travimadox100 × 100 mm76 parts2LMIT0DataAcq-Receiver
lhr-solar
22.8 × 36.5 mm37 parts4LNo license0Evalboard2
mschuldt
60.4 × 71.3 mm31 parts2LNo license6Top
StanZalewski
100 × 66.2 mm57 parts4LNo license0
How designs wire the FT234XD-R
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the FT234XD-R connects to, and the resistors, capacitors and other passives placed on it.
- The USBDM pin has a series resistor on 5 of 5 designs, most often 27 Ω.
- The USBDP pin has a series resistor on 5 of 5 designs, most often 27 Ω.
- The CBUS0 pin is left unconnected on 5 of 5 designs.
- The RESET# pin has a capacitor to GND on 4 of 5 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| USBDMpin 1 | Connected to: Signal 100% |
|
| RESET#pin 2 | Connected to: Signal 80% · not connected 20% |
|
| 3V3OUTpin 3 | Connected to: Signal 80% · not connected 20% |
|
| VCCpin 4 | Connected to: VBUS_SLAVE 80% · a signal 20% |
|
| GNDpin 5, 13 | Connected to: GND 100% | — |
| CBUS0pin 6 | Connected to: Not connected 100% | — |
| RTS#pin 8 | Connected to: Not connected 60% · a signal 40% | — |
| VCCIOpin 9 | Connected to: Signal 80% · 1.8V 20% |
|
| CTS#pin 11 | Connected to: Not connected 80% · a signal 20% | — |
| USBDPpin 12 | Connected to: Signal 100% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Scalenode cm4-baseboard by antmicro, Evalboard1 by mschuldt, DataAcq-Receiver by lhr-solar and Top PCB by StanZalewski.
The FT234XD-R in open source designs
The gallery holds 6 open source boards using the FT234XD-R from 5 GitHub repositories; a typical one measures about 83.8 × 55.7 mm and carries around 47 components.
50% are two-layer designs, the rest use four layers or more, and 33% carry an open source license.
The most starred is Scalenode cm4-baseboard by antmicro.
Microcontrollers on boards using the FT234XD-R
What boards using the FT234XD-R are built for
FT234XD-R: common questions
Where can I find a FT234XD-R reference design?
Each of the 6 boards on this page is a real design using the FT234XD-R. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the FT234XD-R USBDM pin?
The USBDM pin has a series resistor on 5 of 5 designs, most often 27 Ω. Counted from the KiCad layouts of 5 open source designs using the FT234XD-R.
What resistor goes on the FT234XD-R USBDP pin?
The USBDP pin has a series resistor on 5 of 5 designs, most often 27 Ω. Counted from the KiCad layouts of 5 open source designs using the FT234XD-R.
How is the FT234XD-R CBUS0 pin connected?
The CBUS0 pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the FT234XD-R.
Which microcontrollers do boards using the FT234XD-R use?
Most are built on Raspberry Pi (1) and STM32 (1).
How big is a typical board using the FT234XD-R?
The median is 83.8 × 55.7 mm, and 50% are two-layer designs.
What is the most popular open source board using the FT234XD-R?
By GitHub stars, Scalenode cm4-baseboard by antmicro, with 151 stars.
Can I simulate one of these boards using the FT234XD-R before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.