8 open source boards using the INA219BIDR

Real designs built with the INA219BIDR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

8 boardsClear filters|Most starred

How designs wire the INA219BIDR

Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the INA219BIDR connects to, and the resistors, capacitors and other passives placed on it.

  • The VS pin has a decoupling capacitor on 6 of 7 designs, most often 100 nF.
  • The SDA pin has a pull-up to 3.3V on 5 of 7 designs, most often 10 kΩ (then 3.3 kΩ).
  • The SCL pin has a pull-up to 3.3V on 5 of 7 designs, most often 10 kΩ (then 3.3 kΩ).
  • The VIN+ pin has a series resistor on 5 of 7 designs, most often 40 mΩ (then 0 Ω).
A1pin 1Connected to: GND 71% · a signal 29%
SDApin 3Connected to: A connector 43%
  • Pull-up to 3.3V on 71% · 10 kΩ (6), 3.3 kΩ (1)
SCLpin 4Connected to: A connector 43%, the microcontroller 29%
  • Pull-up to 3.3V on 71% · 10 kΩ (6), 3.3 kΩ (1)
VSpin 5Connected to: 3.3V 100%
  • Decoupling capacitor on 86% · 100 nF (7)
GNDpin 6Connected to: GND 86%
VIN-pin 7Connected to: A connector 29% · VBAT 43%
  • Series resistor on 43% · 40 mΩ (1), 10 Ω (1), 10 mΩ (1)
VIN+pin 8Connected to: A connector 29% · VIN1 29%
  • Series resistor on 71% · 40 mΩ (1), 0 Ω (1), 1.8 kΩ (1)

1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Batteryboard bottom by AFS-pt, SnapHAT main board by marchmare, SB Pixel Count by computergeek1507 and Experiment Carrier Board by andrempmattos.

The INA219BIDR in open source designs

The gallery holds 8 open source boards using the INA219BIDR from 8 GitHub repositories; a typical one measures about 63 × 65.5 mm and carries around 39 components.

71% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.

The most starred is Batteryboard bottom by AFS-pt.

Microcontrollers on boards using the INA219BIDR

INA219BIDR: common questions

Where can I find a INA219BIDR reference design?

Each of the 8 boards on this page is a real design using the INA219BIDR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What decoupling capacitors do designs use on the INA219BIDR VS pin?

The VS pin has a decoupling capacitor on 6 of 7 designs, most often 100 nF. Counted from the KiCad layouts of 7 open source designs using the INA219BIDR.

What pull-up resistor is used on the INA219BIDR SDA pin?

The SDA pin has a pull-up to 3.3V on 5 of 7 designs, most often 10 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 7 open source designs using the INA219BIDR.

What pull-up resistor is used on the INA219BIDR SCL pin?

The SCL pin has a pull-up to 3.3V on 5 of 7 designs, most often 10 kΩ (then 3.3 kΩ). Counted from the KiCad layouts of 7 open source designs using the INA219BIDR.

Which microcontrollers do boards using the INA219BIDR use?

Most are built on ESP32 (2), AVR/Arduino (1) and Raspberry Pi (1).

How big is a typical board using the INA219BIDR?

The median is 63 × 65.5 mm, and 71% are two-layer designs.

What is the most popular open source board using the INA219BIDR?

By GitHub stars, Batteryboard bottom by AFS-pt, with 15 stars.

Can I simulate one of these boards using the INA219BIDR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part