8 open source boards using the INA240A1D
Real designs built with the INA240A1D, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Microchip SAM
WPT TX
mark-belbin
100 × 45 mm117 parts4LGPL-3.073LM puissance
Gokay-git
175 × 70 mm69 parts2LNo license1STM32
RC Charger
aokblast
200 × 100 mm296 parts4LNo license0STM32
Stmservo
he1k
60 × 60 mm70 parts4LNo license0Model-Predictive-Control-Strategies for-Fourth-Order-Power-Converters
aguscsc
76 × 53 mm23 parts2LNo license0RP2040/RP2350
Driver Module
Twisted-Fields
68.8 × 36 mm107 parts4LCustom license419WPT RX
mark-belbin
100 × 45 mm51 parts4LGPL-3.073MicroDeflect
tullulah
100 × 100 mm94 parts2LGPL-3.03
How designs wire the INA240A1D
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the INA240A1D connects to, and the resistors, capacitors and other passives placed on it.
- The - pin has a series resistor on 7 of 7 designs, most often 3 mΩ (then 400 Ω).
- The + pin has a series resistor on 6 of 7 designs, most often 3 mΩ (then 100 mΩ).
- The V+ pin has a decoupling capacitor on 4 of 7 designs, most often 100 nF (then 10 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| -pin 1 | Connected to: A connector 57% |
|
| GNDpin 2, 4 | Connected to: GND 93% | — |
| V+pin 6 | Connected to: 3.3V 86% |
|
| +pin 8 | Connected to: A connector 43% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Driver Module by Twisted-Fields, WPT RX by mark-belbin, MicroDeflect by tullulah and LM puissance by Gokay-git.
The INA240A1D in open source designs
The gallery holds 8 open source boards using the INA240A1D from 7 GitHub repositories; a typical one measures about 100 × 56.5 mm and carries around 82 components.
63% use four copper layers or more, and 38% carry an open source license.
The most starred is Driver Module by Twisted-Fields.
Parts used alongside the INA240A1D
Microcontrollers on boards using the INA240A1D
What boards using the INA240A1D are built for
INA240A1D: common questions
Where can I find a INA240A1D reference design?
Each of the 8 boards on this page is a real design using the INA240A1D. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the INA240A1D - pin?
The - pin has a series resistor on 7 of 7 designs, most often 3 mΩ (then 400 Ω). Counted from the KiCad layouts of 7 open source designs using the INA240A1D.
What resistor goes on the INA240A1D + pin?
The + pin has a series resistor on 6 of 7 designs, most often 3 mΩ (then 100 mΩ). Counted from the KiCad layouts of 7 open source designs using the INA240A1D.
What decoupling capacitors do designs use on the INA240A1D V+ pin?
The V+ pin has a decoupling capacitor on 4 of 7 designs, most often 100 nF (then 10 nF). Counted from the KiCad layouts of 7 open source designs using the INA240A1D.
Which microcontrollers do boards using the INA240A1D use?
Most are built on STM32 (2), RP2040/RP2350 (1) and Microchip SAM (1).
How big is a typical board using the INA240A1D?
The median is 100 × 56.5 mm, and 38% are two-layer designs.
What is the most popular open source board using the INA240A1D?
By GitHub stars, Driver Module by Twisted-Fields, with 419 stars.
Can I simulate one of these boards using the INA240A1D before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.