5 open source boards using the IS25LP064A-JBLE
Real designs built with the IS25LP064A-JBLE, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Imxrt1020-module
martinribelotta
136 × 58 mm133 parts2LBSD-3-Clause37NXP
Dropbot control board.
sci-bots
115 × 92 mm141 partsCustom license1STM32
Teresina-Rack
marcoallegretti
68 × 40 mm209 parts12LNo license0STM32
Teresina
marcoallegretti
18 × 52.5 mm86 parts12LNo license0Microchip SAM
Hermes
1337bowen
50 × 80 mm69 parts4LMIT0
How designs wire the IS25LP064A-JBLE
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the IS25LP064A-JBLE connects to, and the resistors, capacitors and other passives placed on it.
- Pin 4 is tied to GND on 5 of 5 designs.
- Pin 8 is tied to 3.3V on 4 of 5 designs.
- Pin 1 has a pull-up to 3.3V on 3 of 5 designs, most often 10 kΩ (then 5.1 kΩ).
- Pin 8 has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: The microcontroller 80% |
|
| Pin 4 | Connected to: GND 100% | — |
| Pin 8 | Connected to: 3.3V 80% · a signal 20% |
|
5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Imxrt1020-module by martinribelotta, Dropbot control board.kicad by sci-bots, Hermes by 1337bowen and Teresina by marcoallegretti.
The IS25LP064A-JBLE in open source designs
The gallery holds 5 open source boards using the IS25LP064A-JBLE from 5 GitHub repositories; a typical one measures about 68 × 58 mm and carries around 133 components.
75% use four copper layers or more, and 40% carry an open source license.
The most starred is Imxrt1020-module by martinribelotta.
Parts used alongside the IS25LP064A-JBLE
Microcontrollers on boards using the IS25LP064A-JBLE
What boards using the IS25LP064A-JBLE are built for
IS25LP064A-JBLE: common questions
Where can I find a IS25LP064A-JBLE reference design?
Each of the 5 boards on this page is a real design using the IS25LP064A-JBLE. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the IS25LP064A-JBLE pin 4 connected?
Pin 4 is tied to GND on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the IS25LP064A-JBLE.
How is the IS25LP064A-JBLE pin 8 connected?
Pin 8 is tied to 3.3V on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the IS25LP064A-JBLE.
What pull-up resistor is used on the IS25LP064A-JBLE pin 1?
Pin 1 has a pull-up to 3.3V on 3 of 5 designs, most often 10 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 5 open source designs using the IS25LP064A-JBLE.
What parts are used alongside the IS25LP064A-JBLE?
The PCM3060PWR, STM32H750IBK6, TPS62170DSGR and USBLC6-2SC6 appear in the most repositories here.
Which microcontrollers do boards using the IS25LP064A-JBLE use?
Most are built on STM32 (2), NXP (1) and Microchip SAM (1).
How big is a typical board using the IS25LP064A-JBLE?
The median is 68 × 58 mm, and 25% are two-layer designs.
What is the most popular open source board using the IS25LP064A-JBLE?
By GitHub stars, Imxrt1020-module by martinribelotta, with 37 stars.
Can I simulate one of these boards using the IS25LP064A-JBLE before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.