12 open source boards using the L298P
Real designs built with the L298P, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
ATMEGA328-Motor-Board
AntonioMR
77 × 100 mm171 parts2LNo license39ESP32
IndegoRover
MS71
172 × 230 mm28 parts2LNo license7AVR/Arduino
Sparkdog-PF-DI-V3
RabbitECUProject
104.1 × 98.9 mm212 parts4LBSD-2-Clause1ESP32
HapticCopiloting
bri-yan
119.4 × 127 mm84 parts2LNo license1TCAR Motor Board - L298P
tronixio
80 × 140 mm135 parts2LNo license0AVR/Arduino
Shield offset
apmarshall3
83.2 × 78.1 mm125 parts4LNo license0AVR/Arduino
Arduino DCC++
danielvilas
100 × 88 mm89 parts2LMIT0ESP32
CUSTOM ROBOT PCB WITH ESP32
bejaouihamza
49 × 110.5 mm56 parts2LNo license0NXP
Wasabi
PeterRice4
83 × 57.5 mm49 parts2LNo license0AVR/Arduino
Shield
apmarshall3
83.2 × 69.2 mm82 parts2LNo license0NXP
Wasabi.v1.1
PeterRice4
68.8 × 54.5 mm10 parts2LNo license0BoostModule
danielvilas
100 × 50 mm40 parts2LMIT0
How designs wire the L298P
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the L298P connects to, and the resistors, capacitors and other passives placed on it.
- The SENSE_A pin has a resistor to GND on 7 of 9 designs, most often 1 Ω (then 20 mΩ).
- The SENSE_B pin has a resistor to GND on 6 of 8 designs, most often 1 Ω (then 20 mΩ).
- The VSS pin has a decoupling capacitor on 5 of 8 designs, most often 100 nF.
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1, 10, 11, 20 | Connected to: GND 97% | — |
| SENSE_Apin 2 | Connected to: The microcontroller 22% · not connected 22% |
|
| NCpin 3, 18 | Connected to: Not connected 94% | — |
| OUT1pin 4 | Connected to: A connector 67% |
|
| VSpin 6 | Connected to: 12V 44% · a signal 33% |
|
| IN1pin 7 | Connected to: The microcontroller 33%, a connector 22% |
|
| VSSpin 12 | Connected to: 5V 100% |
|
| OUT4pin 17 | Connected to: A connector 75% |
|
| SENSE_Bpin 19 | Connected to: The microcontroller 25% · not connected 25% |
|
8 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include ATMEGA328-Motor-Board by AntonioMR, IndegoRover by MS71, HapticCopiloting by bri-yan and Sparkdog-PF-DI-V3 by RabbitECUProject.
The L298P in open source designs
The gallery holds 12 open source boards using the L298P from 9 GitHub repositories; a typical one measures about 83.2 × 93.5 mm and carries around 83 components.
83% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.
The most starred is ATMEGA328-Motor-Board by AntonioMR.
Microcontrollers on boards using the L298P
What boards using the L298P are built for
L298P: common questions
Where can I find a L298P reference design?
Each of the 12 boards on this page is a real design using the L298P. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the L298P SENSE_A pin?
The SENSE_A pin has a resistor to GND on 7 of 9 designs, most often 1 Ω (then 20 mΩ). Counted from the KiCad layouts of 9 open source designs using the L298P.
What resistor goes on the L298P SENSE_B pin?
The SENSE_B pin has a resistor to GND on 6 of 8 designs, most often 1 Ω (then 20 mΩ). Counted from the KiCad layouts of 9 open source designs using the L298P.
What decoupling capacitors do designs use on the L298P VSS pin?
The VSS pin has a decoupling capacitor on 5 of 8 designs, most often 100 nF. Counted from the KiCad layouts of 9 open source designs using the L298P.
Which microcontrollers do boards using the L298P use?
Most are built on AVR/Arduino (5), ESP32 (3) and NXP (2).
How big is a typical board using the L298P?
The median is 83.2 × 93.5 mm, and 83% are two-layer designs.
What is the most popular open source board using the L298P?
By GitHub stars, ATMEGA328-Motor-Board by AntonioMR, with 39 stars.
Can I simulate one of these boards using the L298P before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.