6 open source boards using the L5973D
Real designs built with the L5973D, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Lboard2
electrodyssey
203.2 × 101.6 mm214 parts4LLGPL-3.07ESP32
DangerDoughnut
gavin4d
50 × 37 mm152 parts4LNo license1STM32
Arachne
TheColonelYoung
100 × 70 mm265 parts2LGPL-3.00ESP8266
RGBW-Lampe
martinclausen2
99.6 × 69.6 mm155 parts2LNo license03D PrEBo
TheColonelYoung
100 × 84 mm71 parts2LCC-BY-SA-4.00Ivegotdapower elec board fille
PhenixRobotik
44.5 × 20.3 mm36 parts2LNo license0
How designs wire the L5973D
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the L5973D connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin has a inductor on 6 of 6 designs, most often 15 µH.
- The COMP pin has a series capacitor on 6 of 6 designs, most often 22 nF.
- The COMP pin has a capacitor to GND on 6 of 6 designs, most often 220 pF (then 220 nF).
- The FB pin has a resistor to GND on 6 of 6 designs, most often 10 kΩ (then 3.9 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| OUTpin 1 | Connected to: Signal 100% |
|
| SYNCpin 2 | Connected to: Not connected 83% · a signal 17% | — |
| INHpin 3 | Connected to: GND 83% · a signal 17% | — |
| COMPpin 4 | Connected to: Signal 100% |
|
| FBpin 5 | Connected to: Signal 100% |
|
| VREFpin 6 | Connected to: Not connected 67% · a signal 33% | — |
| GNDpin 7 | Connected to: GND 100% | — |
| VCCpin 8 | Connected to: BATT 50% · a signal 50% |
|
| EPpin 9 | Connected to: GND 83% · not connected 17% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Lboard2 by electrodyssey, DangerDoughnut by gavin4d, RGBW-Lampe by martinclausen2 and Ivegotdapower elec board fille by PhenixRobotik.
The L5973D in open source designs
The gallery holds 6 open source boards using the L5973D from 6 GitHub repositories; a typical one measures about 99.8 × 69.8 mm and carries around 154 components.
67% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Lboard2 by electrodyssey.
Parts used alongside the L5973D
What boards using the L5973D are built for
L5973D: common questions
Where can I find a L5973D reference design?
Each of the 6 boards on this page is a real design using the L5973D. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the L5973D OUT pin connected?
The OUT pin has a inductor on 6 of 6 designs, most often 15 µH. Counted from the KiCad layouts of 6 open source designs using the L5973D.
How is the L5973D COMP pin connected?
The COMP pin has a series capacitor on 6 of 6 designs, most often 22 nF. Counted from the KiCad layouts of 6 open source designs using the L5973D.
What resistor goes on the L5973D FB pin?
The FB pin has a resistor to GND on 6 of 6 designs, most often 10 kΩ (then 3.9 kΩ). Counted from the KiCad layouts of 6 open source designs using the L5973D.
What parts are used alongside the L5973D?
The NCP1117-3.3_SOT223, NCP1117-5.0_SOT223 and USBLC6-2SC6 appear in the most repositories here.
Which microcontrollers do boards using the L5973D use?
Most are built on STM32 (2), ESP32 (1) and ESP8266 (1).
How big is a typical board using the L5973D?
The median is 99.8 × 69.8 mm, and 67% are two-layer designs.
What is the most popular open source board using the L5973D?
By GitHub stars, Lboard2 by electrodyssey, with 7 stars.
Can I simulate one of these boards using the L5973D before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.