9 open source boards using the LF33_TO220
Real designs built with the LF33_TO220, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Meteo station
alicjamusial
110 × 90 mm23 parts2LCC-BY-SA-4.08AVR/Arduino
Ws 3.0
boanjo
72.7 × 114 mm53 parts2LNo license4Tester circut
yazidta
69.6 × 101.6 mm49 parts2LNo license3ESP32
Jammer
aryakaithal8
53.1 × 100.5 mm90 parts2LNo license0Saturation meter
AntoninPvr
138 × 111 mm50 parts2LNo license0Control panel
jevans3142
69.9 × 67.3 mm35 parts2LNo license1Dash
formulaslug
79.5 × 57 mm38 parts2LNo license5STM32
X1
embeddedalpha
30 × 80 mm57 parts2LMIT75Live Telemetry Board
formulaslug
108.8 × 73.1 mm18 parts2LNo license5
How designs wire the LF33_TO220
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the LF33_TO220 connects to, and the resistors, capacitors and other passives placed on it.
- The VI pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 10 µF).
- The VO pin has a decoupling capacitor on 4 of 8 designs, most often 2.2 µF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VIpin 1 | Connected to: 5V 75% · a signal 25% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| VOpin 3 | Connected to: 3.3V 100% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include X1 by embeddedalpha, Meteo station pcb by alicjamusial, Dash by formulaslug and Ws 3.0 by boanjo.
The LF33_TO220 in open source designs
The gallery holds 9 open source boards using the LF33_TO220 from 8 GitHub repositories; a typical one measures about 72.7 × 90 mm and carries around 49 components.
100% are two-layer designs, the rest use four layers or more, and 22% carry an open source license.
The most starred is X1 by embeddedalpha.
Parts used alongside the LF33_TO220
Microcontrollers on boards using the LF33_TO220
What boards using the LF33_TO220 are built for
LF33_TO220: common questions
Where can I find a LF33_TO220 reference design?
Each of the 9 boards on this page is a real design using the LF33_TO220. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the LF33_TO220 VI pin?
The VI pin has a decoupling capacitor on 6 of 8 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 8 open source designs using the LF33_TO220.
What decoupling capacitors do designs use on the LF33_TO220 VO pin?
The VO pin has a decoupling capacitor on 4 of 8 designs, most often 2.2 µF (then 100 nF). Counted from the KiCad layouts of 8 open source designs using the LF33_TO220.
Which microcontrollers do boards using the LF33_TO220 use?
Most are built on ESP32 (2), AVR/Arduino (1) and STM32 (1).
How big is a typical board using the LF33_TO220?
The median is 72.7 × 90 mm, and 100% are two-layer designs.
What is the most popular open source board using the LF33_TO220?
By GitHub stars, X1 by embeddedalpha, with 75 stars.
Can I simulate one of these boards using the LF33_TO220 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.