11 open source boards using the LM2596T-ADJ
Real designs built with the LM2596T-ADJ, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Zx sizif-512
UzixLS
213 × 65.1 mm203 parts2LMIT194Dendy
UzixLS
91 × 186.5 mm127 parts2LNo license19ESP32
BlueJamma
KPEKEP
110.4 × 62.8 mm29 parts2LNo license3Raspberry Pi
CrallyBoard
cruunnerr
180.7 × 143.8 mm226 parts2LNo license0ESP32
Domoticata main control unit
LoZioo
151.8 × 95.4 mm128 parts2LMIT0ESP32
ESP32 BUCK WLED NO BOARD OLD
lepetidozo
109.3 × 71.4 mm38 parts4LNo license0- schematic only · 7 parts
Dual power supply
notAbhay321
7 partsMIT0 ESP32
ESP32 BUCK WLED NO BOARD
lepetidozo
55.9 × 78.7 mm37 parts4LNo license0DD Power 1
Acmex2564
110 × 47.8 mm91 parts4LNo license19DD Power 2
Acmex2564
110 × 47.8 mm51 parts2LNo license19Carte de puissance Euro
Rami-Troudi
87.1 × 81.1 mm30 parts2LNo license1
How designs wire the LM2596T-ADJ
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the LM2596T-ADJ connects to, and the resistors, capacitors and other passives placed on it.
- The OUT pin has a inductor on 7 of 8 designs, most often 47 µH (then 33 µH).
- The VIN pin has a capacitor to GND on 5 of 8 designs, most often 100 nF (then 100 µF).
- The FB pin has a pull-up to 5V on 5 of 8 designs, most often 3 kΩ (then 1 kΩ).
- The FB pin has a resistor to GND on 5 of 8 designs, most often 1 kΩ (then 976 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VINpin 1 | Connected to: Signal 63% · 12V 25% |
|
| OUTpin 2 | Connected to: Signal 88% |
|
| GNDpin 3 | Connected to: GND 88% | — |
| FBpin 4 | Connected to: Signal 88% |
|
| ON/OFFpin 5 | Connected to: GND 75% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Zx sizif-512 by UzixLS, DD Power 1 by Acmex2564, Dendy by UzixLS and BlueJamma by KPEKEP.
The LM2596T-ADJ in open source designs
The gallery holds 11 open source boards using the LM2596T-ADJ from 9 GitHub repositories; a typical one measures about 110 × 75.1 mm and carries around 51 components.
70% are two-layer designs, the rest use four layers or more, and 27% carry an open source license.
The most starred is Zx sizif-512 by UzixLS.
Parts used alongside the LM2596T-ADJ
Microcontrollers on boards using the LM2596T-ADJ
What boards using the LM2596T-ADJ are built for
LM2596T-ADJ: common questions
Where can I find a LM2596T-ADJ reference design?
Each of the 11 boards on this page is a real design using the LM2596T-ADJ. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM2596T-ADJ OUT pin connected?
The OUT pin has a inductor on 7 of 8 designs, most often 47 µH (then 33 µH). Counted from the KiCad layouts of 8 open source designs using the LM2596T-ADJ.
How is the LM2596T-ADJ VIN pin connected?
The VIN pin has a capacitor to GND on 5 of 8 designs, most often 100 nF (then 100 µF). Counted from the KiCad layouts of 8 open source designs using the LM2596T-ADJ.
What pull-up resistor is used on the LM2596T-ADJ FB pin?
The FB pin has a pull-up to 5V on 5 of 8 designs, most often 3 kΩ (then 1 kΩ). Counted from the KiCad layouts of 8 open source designs using the LM2596T-ADJ.
Which microcontrollers do boards using the LM2596T-ADJ use?
Most are built on ESP32 (4) and Raspberry Pi (1).
How big is a typical board using the LM2596T-ADJ?
The median is 110 × 75.1 mm, and 70% are two-layer designs.
What is the most popular open source board using the LM2596T-ADJ?
By GitHub stars, Zx sizif-512 by UzixLS, with 194 stars.
Can I simulate one of these boards using the LM2596T-ADJ before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.