7 open source boards using the LM556
Real designs built with the LM556, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Poly555
oskitone
184 × 114.8 mm248 parts2LCustom license91JC2 v4.1
Emile666
233.7 × 160 mm120 parts2LNo license3Clock circuit
bit4man
145.4 × 95.5 mm63 parts2LNo license0One-Shot-Blinking-Light
mlp6
86.4 × 76.2 mm20 parts2LNo license0RC1 CPU
tebl
99.1 × 99.1 mm45 parts2LCERN-OHL-1.225MUTIF09 Single Board Computer
ja1umi
155 × 114 mm68 parts2LMIT1016PinSocketAPC
michaelshiloh
53.6 × 40.4 mm3 parts2LAGPL-3.014
How designs wire the LM556
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the LM556 connects to, and the resistors, capacitors and other passives placed on it.
- The THR pins have a series resistor on 5 of 7 designs, most often 1 kΩ (then 2.2 kΩ).
- The THR pins have a capacitor to GND on 5 of 7 designs, most often 1 µF (then 220 nF).
- The TR pins have a series resistor on 5 of 7 designs, most often 1 kΩ (then 2.2 kΩ).
- The TR pins have a capacitor to GND on 5 of 7 designs, most often 1 µF (then 220 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| DISpin 1, 13 | Connected to: A connector 36%, 6502 29% |
|
| THRpin 2, 12 | Connected to: Signal 100% |
|
| CVpin 3, 11 | Connected to: Signal 57% · not connected 43% |
|
| Rpin 4, 10 | Connected to: VCC 71% · a signal 21% | — |
| Qpin 5, 9 | Connected to: Signal 64% · not connected 36% |
|
| TRpin 6, 8 | Connected to: Signal 93% |
|
| GNDpin 7 | Connected to: GND 71% · a signal 29% | — |
| VCCpin 14 | Connected to: 5V 86% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Poly555 by oskitone, RC1 CPU by tebl, 16PinSocketAPC by michaelshiloh and MUTIF09 Single Board Computer by ja1umi.
The LM556 in open source designs
The gallery holds 7 open source boards using the LM556 from 7 GitHub repositories; a typical one measures about 145.4 × 99.1 mm and carries around 63 components.
100% are two-layer designs, the rest use four layers or more, and 43% carry an open source license.
The most starred is Poly555 by oskitone.
What boards using the LM556 are built for
LM556: common questions
Where can I find a LM556 reference design?
Each of the 7 boards on this page is a real design using the LM556. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LM556 THR pin?
The THR pins have a series resistor on 5 of 7 designs, most often 1 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 7 open source designs using the LM556.
What resistor goes on the LM556 TR pin?
The TR pins have a series resistor on 5 of 7 designs, most often 1 kΩ (then 2.2 kΩ). Counted from the KiCad layouts of 7 open source designs using the LM556.
How is the LM556 R pin connected?
The R pins is tied to VCC on 71% of them (a signal on 3). Counted from the KiCad layouts of 7 open source designs using the LM556.
What parts are used alongside the LM556?
The 6502, 6532 and 74LS00 appear in the most repositories here.
How big is a typical board using the LM556?
The median is 145.4 × 99.1 mm, and 100% are two-layer designs.
What is the most popular open source board using the LM556?
By GitHub stars, Poly555 by oskitone, with 91 stars.
Can I simulate one of these boards using the LM556 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.