13 open source boards using the LM74700
Real designs built with the LM74700, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Lattepanda MOKA
piecol
100 × 70.1 mm207 parts4LCERN-OHL-S-2.035ESP32
OSSM ALT SERVO V3 4
jollydodo
55 × 50 mm120 parts4LCustom license31STM32
CanardBoard
waterloo-rocketry
100 × 70 mm244 parts6LGPL-3.015RP2040/RP2350
Hardware
seedhammer
205.3 × 78 mm172 parts4LUnlicense9ESP32
Open Shot Clock Display
DLaxV-Community-Projects-Hub
100 × 75 mm196 parts2LCERN-OHL-P-2.05Raspberry Pi
Masters thesis lora gateway compute module cubesat payload
dpmj
90.2 × 95.9 mm338 parts6LCERN-OHL-S-2.02Spinali mcxn t1 hub
CogniPilot
36.5 × 46 mm203 parts6LApache-2.02RP2040/RP2350
FinalProject
leomotors
100 × 100 mm139 parts2LNo license1RP2040/RP2350
IoAmp200W
ilolson
85.5 × 54 mm365 parts6LMIT0ESP32
Open Shot Clock Controller
DLaxV-Community-Projects-Hub
100 × 47.5 mm164 parts2LCERN-OHL-P-2.05P1 rx
Deco025
75 × 60 mm86 parts4LCERN-OHL-S-2.04RP2040/RP2350
SMOL-SERVO-RP-NDRV
dognotdog
42 × 42 mm84 parts4LCustom license5Ideal diode
oskarengdahl
70 × 50 mm14 parts2LNo license0
How designs wire the LM74700
Read from the KiCad layouts of 12 open source designs, one per repository: what each pin of the LM74700 connects to, and the resistors, capacitors and other passives placed on it.
- The EN pin has a series capacitor on 7 of 12 designs, most often 100 nF.
- The VCAP pin has a capacitor to the supply on 6 of 12 designs, most often 100 nF.
- The VCAP pin has a series capacitor on 6 of 12 designs, most often 100 nF.
- The EN pin has a capacitor to GND on 6 of 12 designs, most often 100 nF (then 22 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VCAPpin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| ENpin 3 | Connected to: A connector 25% · 15V 33% |
|
3 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Lattepanda MOKA by piecol, OSSM ALT SERVO V3 4 by jollydodo, CanardBoard by waterloo-rocketry and Hardware by seedhammer.
The LM74700 in open source designs
The gallery holds 13 open source boards using the LM74700 from 12 GitHub repositories; a typical one measures about 90.2 × 60 mm and carries around 172 components.
69% use four copper layers or more, and 69% carry an open source license.
The most starred is Lattepanda MOKA by piecol.
Parts used alongside the LM74700
Microcontrollers on boards using the LM74700
What boards using the LM74700 are built for
LM74700: common questions
Where can I find a LM74700 reference design?
Each of the 13 boards on this page is a real design using the LM74700. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM74700 EN pin connected?
The EN pin has a series capacitor on 7 of 12 designs, most often 100 nF. Counted from the KiCad layouts of 12 open source designs using the LM74700.
How is the LM74700 VCAP pin connected?
The VCAP pin has a capacitor to the supply on 6 of 12 designs, most often 100 nF. Counted from the KiCad layouts of 12 open source designs using the LM74700.
Which microcontrollers do boards using the LM74700 use?
Most are built on RP2040/RP2350 (4), ESP32 (3), Raspberry Pi (1) and STM32 (1).
How big is a typical board using the LM74700?
The median is 90.2 × 60 mm, and 31% are two-layer designs.
What is the most popular open source board using the LM74700?
By GitHub stars, Lattepanda MOKA by piecol, with 35 stars.
Can I simulate one of these boards using the LM74700 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.