10 open source boards using the LM833
Real designs built with the LM833, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Analog rev3
PaulStoffregen
50.8 × 108 mm200 parts2LNo license160LIA
JasMoH
290.9 × 87.4 mm295 parts2LGPL-3.05Input Board
jensenr30
100 × 100 mm93 parts2LNo license1AVR/Arduino
AmplifierBoard
dangrie158
210 × 104 mm225 parts2LMIT0BeavisUltrasound
tonnieshod967
208.3 × 107.3 mm187 parts4LCERN-OHL-P-2.00Turtable control board hbridge
trublion
89.4 × 50 mm106 parts2LMIT0Turtable control board servo
trublion
90 × 90 mm84 parts2LMIT0LNA test
JasMoH
70.4 × 35.3 mm109 parts2LGPL-3.05Input Board Panel
jensenr30
100 × 100 mm93 parts2LNo license1Pll test
JasMoH
71.9 × 17.5 mm81 parts2LGPL-3.05
How designs wire the LM833
Read from the KiCad layouts of 7 open source designs, one per repository: what each pin of the LM833 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 1 has a series resistor on 7 of 7 designs, most often 100 Ω (then 3.84 kΩ).
- Pin 7 has a series resistor on 7 of 7 designs, most often 75 kΩ (then 220 Ω).
- Pin 1 has a series capacitor on 6 of 7 designs, most often 100 pF (then 1 nF).
- The - pins have a series resistor on 6 of 7 designs, most often 10 kΩ (then 2.21 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 1 | Connected to: Signal 100% |
|
| -pin 2, 6 | Connected to: Signal 100% |
|
| +pin 3, 5 | Connected to: A connector 21% |
|
| V-pin 4 | Connected to: -12V 57% · GND 29% |
|
| Pin 7 | Connected to: Signal 100% |
|
| V+pin 8 | Connected to: 12V 57% · a signal 43% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Analog rev3 by PaulStoffregen, LIA by JasMoH, Input Board by jensenr30 and AmplifierBoard by dangrie158.
The LM833 in open source designs
The gallery holds 10 open source boards using the LM833 from 7 GitHub repositories; a typical one measures about 95 × 95 mm and carries around 108 components.
90% are two-layer designs, the rest use four layers or more, and 70% carry an open source license.
The most starred is Analog rev3 by PaulStoffregen.
Parts used alongside the LM833
Microcontrollers on boards using the LM833
What boards using the LM833 are built for
LM833: common questions
Where can I find a LM833 reference design?
Each of the 10 boards on this page is a real design using the LM833. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the LM833 pin 1?
Pin 1 has a series resistor on 7 of 7 designs, most often 100 Ω (then 3.84 kΩ). Counted from the KiCad layouts of 7 open source designs using the LM833.
What resistor goes on the LM833 pin 7?
Pin 7 has a series resistor on 7 of 7 designs, most often 75 kΩ (then 220 Ω). Counted from the KiCad layouts of 7 open source designs using the LM833.
What resistor goes on the LM833 - pin?
The - pins have a series resistor on 6 of 7 designs, most often 10 kΩ (then 2.21 kΩ). Counted from the KiCad layouts of 7 open source designs using the LM833.
What parts are used alongside the LM833?
The LM358, 74HC14, LM2674 and LM7805_TO220 appear in the most repositories here.
Which microcontrollers do boards using the LM833 use?
Most are built on AVR/Arduino (1).
How big is a typical board using the LM833?
The median is 95 × 95 mm, and 90% are two-layer designs.
What is the most popular open source board using the LM833?
By GitHub stars, Analog rev3 by PaulStoffregen, with 160 stars.
Can I simulate one of these boards using the LM833 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.