6 open source boards using the LMR38010SDDAR
Real designs built with the LMR38010SDDAR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Bms c1
LibreSolar
135 × 70 mm167 parts4LCERN-OHL-W-2.0277STM32
Reflow Hot Plate Control Board
ikajdan
80 × 80 mm95 parts2LMIT14RP2040/RP2350
Servodrive — board S, single board
sequoia-hope
65 × 65 mm190 parts6LNo license0ESP32
Libre Solar BMS C1
PawelSroczynski
135 × 70 mm166 parts4LGPL-3.00ESP32
Libre Solar BMS C1
shinemohans061
135 × 70 mm166 parts4LNo license0ESP32
Esp32-battery charging monitoring
bogdan-kovalchuk
62 × 50 mm60 parts4LMIT0
How designs wire the LMR38010SDDAR
Read from the KiCad layouts of 6 open source designs, one per repository: what each pin of the LMR38010SDDAR connects to, and the resistors, capacitors and other passives placed on it.
- The VIN pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 2.2 µF).
- The RT/SYNC pin has a resistor to GND on 6 of 6 designs, most often 52.3 kΩ (then 25.5 kΩ).
- The FB pin has a resistor to GND on 6 of 6 designs, most often 35.7 kΩ (then 24.9 kΩ).
- The FB pin has a pull-up to 3.3V on 6 of 6 designs, most often 82 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 100% | — |
| ENpin 2 | Connected to: Signal 67% · VIN 33% |
|
| VINpin 3 | Connected to: VIN 100% |
|
| RT/SYNCpin 4 | Connected to: Signal 100% |
|
| FBpin 5 | Connected to: Signal 100% |
|
| PGpin 6 | Connected to: Not connected 100% | — |
| BOOTpin 7 | Connected to: Signal 100% |
|
| SWpin 8 | Connected to: Signal 100% |
|
| PADGNDpin 9 | Connected to: GND 100% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Bms c1 by LibreSolar, Reflow Hot Plate Control Board by ikajdan, Esp32-battery charging monitoring by bogdan-kovalchuk and Libre Solar BMS C1 by PawelSroczynski.
The LMR38010SDDAR in open source designs
The gallery holds 6 open source boards using the LMR38010SDDAR from 6 GitHub repositories; a typical one measures about 107.5 × 70 mm and carries around 166 components.
83% use four copper layers or more, and 67% carry an open source license.
The most starred is Bms c1 by LibreSolar.
Parts used alongside the LMR38010SDDAR
Microcontrollers on boards using the LMR38010SDDAR
What boards using the LMR38010SDDAR are built for
LMR38010SDDAR: common questions
Where can I find a LMR38010SDDAR reference design?
Each of the 6 boards on this page is a real design using the LMR38010SDDAR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What decoupling capacitors do designs use on the LMR38010SDDAR VIN pin?
The VIN pin has a decoupling capacitor on 6 of 6 designs, most often 100 nF (then 2.2 µF). Counted from the KiCad layouts of 6 open source designs using the LMR38010SDDAR.
What resistor goes on the LMR38010SDDAR RT/SYNC pin?
The RT/SYNC pin has a resistor to GND on 6 of 6 designs, most often 52.3 kΩ (then 25.5 kΩ). Counted from the KiCad layouts of 6 open source designs using the LMR38010SDDAR.
What resistor goes on the LMR38010SDDAR FB pin?
The FB pin has a resistor to GND on 6 of 6 designs, most often 35.7 kΩ (then 24.9 kΩ). Counted from the KiCad layouts of 6 open source designs using the LMR38010SDDAR.
What parts are used alongside the LMR38010SDDAR?
The BQ76952PFBR, ESP32-C3-MINI-1-N4, SN65HVD230DR, SN65HVD75DR and USBLC6-2SC6 appear in the most repositories here.
Which microcontrollers do boards using the LMR38010SDDAR use?
Most are built on ESP32 (4), RP2040/RP2350 (1) and STM32 (1).
How big is a typical board using the LMR38010SDDAR?
The median is 107.5 × 70 mm, and 17% are two-layer designs.
What is the most popular open source board using the LMR38010SDDAR?
By GitHub stars, Bms c1 by LibreSolar, with 277 stars.
Can I simulate one of these boards using the LMR38010SDDAR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.